Jump to content
SAU Community

Recommended Posts

Ok. So I was driving on Saturday, and when I gave it a bit (under full boost = 10psi) it would hit a wall kind of like boost cut at 4500rpm for 5 secs then kick into boost again.

Checked over a few things that I thought could be the problem.

1: cleaned afm and plug.

2: tightened intercooler piping and checked for boost leaks.

Nothing worked

Was running and driving fine apart from when I put my foot down.

Then this morning I went to start it up and it wouldn't kick over. So I got a new battery since the one I had was a lil old, put it in and still no dice

All the belts are moving and its just on the point where it wants to kick over, which makes me think it could be the starter motor??

Car was also recently tuned.

Car: Silvia

Engine: Rb25det

Mods include, splitfire coilpacks, turbo back zorst, Apexi avcr, apexi safc, platinum plugs, intercooler, brass button clutch, nothing major.

Any suggestions would be great.

cheers, Ben

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/
Share on other sites

So it's cranking, just not starting? If that's the case, it wouldn't be starter motor. To eliminate that, try jump starting it. If it starts, that'll be the problem. It still would explain the problems under boost.

I would have said coil packs, but you've said their spitfires so that wouldn't be it. Have you had any work done to the car recently?

Check the ignotion system. Is the car getting spark? Is it getting fuel? Are there any plugs that have fallen off? All the vacuum lines attached? I'd check all these first, and then take it to a mechanic.

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4309946
Share on other sites

You need air, fuel and spark to start an engine. Seeming as though you havent listed an aftermarket fuel pump (possibly meaning your still running the 15 year old standard one) under mods that would be the first thing I'll be checking.

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4309984
Share on other sites

try checking the coilpack wiring loom as this can deteriorate overtime which will also cause the car to not start apparently some people who replaced the coilpacks didnt realise that while doing it they might have damaged the wiring as overtime heat caused the wiring to be crispy and would crack easily

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4311013
Share on other sites

Changed the ECU and ignitor module yesterday, neither worked, there was no spark at all. So the problem lies between the module and ECU (as said above, in the harness somewhere).

My thoughts, it could be the resistor?

IS anyone an auto electrician on here or know someone that can come to me as the car doesn't go. For cash :P

Link to comment
https://www.sau.com.au/forums/topic/248397-car-wont-start/#findComment-4311519
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
×
×
  • Create New...