Jump to content
SAU Community

Recommended Posts

Just seen someone here in the UK selling a Stagea RS-four with the RB25DET and an Automatic. This interests me as I was generally under the impression that the Nissan autobox was a bit weak, maximum of 250bhp, and would quickly be killed by an RB25 engine.

Is it a different gearbox in the Stagea or is the Stagea putting out less than 250bhp and thus uses the same gearbox? If it is a better box, how hard would it be to swap it into my AWD Ceffy (along with it's RB25, obviously) how much power is it likely to take?

I'm sure I'm going to get called a poofter for wanting to keep the car auto, but I need something my GF can drive (she has a long term injury to her right shoulder) and it's nice for the hours of stop/start traffic that take up far too much of my driving time over here.

  • 2 weeks later...

Ok been doing some research. Info about Nissan autoboxes is somewhat thin on the ground, but if this site is correct it means that the Ceffy and the Stagea (and the S13 for that matter) use the same gearbox which in turn means I'd be good to go with an RB25 swap.

In the meantime, when my car arrives, I'm going to try this mod. It's designed for an SVX but Subaru and Nissan gearboxes are pretty much the same, basically what it does is instead of pulling out the dropping resistor to get harsher shifts (better for the gearbox, not so good for you) it provides a pressure sensitive switch that pulls the resistor only when the engine is under load (They set it to switch at "6 Hg" I'm guessing since it's American that they mean 6 inHg, so ~ 152 mmHg or 20 kPa) resulting in harsh shifts under acceleration (where you're most likely to do damage to your gearbox if you're making too much power) and normal shifts when you're just pottering about.

That plus a tranny cooler should make the gearbox able to stand up to around 330bhp if my research is correct (and it probably isn't, so I'd like some input here!). So basically it should take a mildly tuned RB25 (or a stock RB26 with the restrictor removed), or I could just go nuts with the RB20 since they're cheap to replace if I blow it! Aiming for around the 300bhp mark, nothing particularly special and still leaves a bit of a safety margin.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’d love to find some where that can recover the dashes to look brand new and original. Mine has a very slight bubble, nothing compared to some I’ve seen though 
    • $170K. I asked one of the guys there as a joke if that price was just for the passenger seat as it was where the price sheet was... he tried really hard to crack a smile 😄 He also mentioned that every single part of the car was inspected and either restored or replaced with a new or as new part, or made from scratch. The interior was incredible, every inch like a new car.
    • Time for a modernisation, throw out the AFM, stock O2s, ECU into the e-waste bin. Rip out the cable throttle, IACV, pedal, etc. into the scrap metal bin. DBW, e-throttle, modern ECU, CANbus wideband, and the thing will drive better than when it left the factory.
    • I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
×
×
  • Create New...