Jump to content
SAU Community

Be careful on repaired vehicles offered for sale out of Japan.

Guest

By Guest,
in General Automotive Discussion

 Share

Recommended Posts

Guest

Guest

Posted
Posted

Be carefull as some people are offering repaired modern cars for sale out of Japan as they are cheap but may end up costing you your car.

The rule is below so read into it dont take somebodys word for it.

A RAW would take all reasonable steps to avoid importing a crash damaged or corroded vehicle.

A RAW wont put up his bussiness to save you money.

In a nut shell they are saying dont bring in a damaged or repaired vehicle. I know of one complyier who knocked back a car as they were told by the importer it is a repaired vehicle but only minor damage. They knocked back the work and said unless you are 100% sure it is minor it will be at your cost. So the buyier went back to the broker who wouldnt sign a document that the car will pass the RAWS inspection then the importer went a bougt a straight as car to save the trouble.

Damaged Vehicles

Crash damage or corrosion may affect continued compliance with the ADRs. This is especially so in the case of the occupant protection ADRs 69, 72 and 73. It is not possible for a RAW to provide a reasonable level of assurance that a crash damaged or corroded vehicle, where the structural integrity of the vehicle has been affected, complies with all of the applicable ADRs. Therefore, it is not permissible for a RAW to fit a used import plate to such a vehicle.

Before commencing compliance work each vehicle must be inspected by the RAW to check for crash damage, damage repair or corrosion that may affect the structural integrity of the vehicle. Records of this inspection are to be retained by the RAW and be made available to VSS inspectors upon request. (Regulation 57)

Crash damaged or corroded vehicles where the structural integrity may be affected must be re-exported or destroyed. It is expected that a RAW would take all reasonable steps to avoid importing a crash damaged or corroded vehicle.

The criteria below must be used as a minimum when deciding if crash damage or corrosion is likely to affect the structural integrity of the vehicle.

q Underbody damage which results in the:

Ø crushing of floorpan stiffening members,

Ø splitting of seam welds or

Ø tearing of the metal

q Damage to rocker panels (or outer sill) which result in:

Ø Dents to a depth of more than 25 mm

Ø Creasing, distortion of the sill weld

q Distortion to longitudinal rails affecting the front and rear crush zones.

q Collision damage to steering or suspension components.

q Damage to the vehicle’s outer body panels, which affect the integrity of any of the seams or joints installed by the vehicle manufacturer.

q Corrosion (rust) which has resulted in perforation or flaking of the metal.

When checking the condition of the vehicle the following items need to be inspected but not necessarily in this order:

q Engine compartment

q Right side

q Luggage cargo compartment

q Left side

q Underbody or chassis frame

q Passenger compartment

Guest

Guest

Posted
Posted

I will always drive a import, Soarer loved it, 180 now that car is fun and RX7 sitting in showroom waiting for me to sell 180.

It is worth it and take advice from people that have nothing to do with the people you are buying off and dont rush.

I have personaly seen a couple of importers telling the truth to buyiers knowing that they wont sell a car to them, they just want to tell the truth, they have a heart beat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      WTB noltec r32 front upper (camber) arms

      By GTSBoy · Posted

      I swear at my GKTech ones every time I have to take them apart and replace a spherical. But I wouldn't swap them for anything else. They absolutely slay every other option, at least in terms of how they actually work. You sure you don't want to live with bearings? I mean, they don't have "ball bearings". They are rod ends and sphericals throughout. Tough as nuts, even though I have found more than one way to wear them out.
    • The Bogan
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By The Bogan · Posted

      From when I was looking at getting the 86 engineered for the turbo, the joint said to put in a few euro 5 or 6 cats, then tune the car on a nice clean E85 tune When I was looking at a turbo for the MX5, it was basically the same thing, a couple of cats and a nice clean tune Although, it will depend on the year of the Jeep IRT emmisions standards required, and what mods are done, especially if it has a newer engine installed that requires a higher Euro
    • GTSBoy
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By GTSBoy · Posted

      Yeah - but it's not actually that easy. There are limits for HC, CO, NOx and particulates. Particulates shouldn't be a concern in any petrol engine unless trying to comply to the very latest Euro standard. But getting a tune right so that all the others stay within limits AT THE SAME TIME is not a trivial exercise. You couldn't possibly get it right by just guessing at the tuner's dyno, unless he had a 4 gas analyser up the pipe, which is not often the case these days. It used to be. Every decent shop that did "tune ups" (as opposed to tuning) would have a 4 gas analsyer. Perhaps there's still quite a few of them around these days. But most "tuners" are only watching O2 and power readings.
    • Shoota_77
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By Shoota_77 · Posted

      Slight segway but the most expensive part of the whole thing which I would have thought would only be required for an engine size/type swap, not a VIV test, is emissions testing.  That's when you get into the big bucks.  I can't remember the exact price now but I got quotes for the GT-R based on swapping to RB30 (not that anyone bothers doing it legally anymore...) and it was around $4500 just for that alone.  The guy that does them manipulates the tune on the vehicle to make sure it passes.  The cheaper option is to book into Kangan Batman Tafe (I think that's where it was) and hire their tester.  Allegedly you're not allowed in there with the car though so not in a position to tweak anything to make sure the vehicle passes.  I'm sure in this day and age of ultra tuneable ECU's you could get the tuner to program a special efficiency (clean) tune that emits the lowest amount of particulates possible that would pass the test.  It might only make 50kW's but as long as it passed who cares!
    • The Bogan
      Neil's R33 Gts-t Build

      By The Bogan · Posted

      I'm sure he has left signs, or, he is looking down, laughing That's my cunning plan for when I leave, lots of half finished projects, with no rhyme or reason of where I was actually up to, just to keep everyone on their toes
×
×
  • Create New...