Jump to content
SAU Community

Be careful on repaired vehicles offered for sale out of Japan.

Guest

By Guest,
in General Automotive Discussion

 Share

Recommended Posts

Guest

Guest

Posted
Posted

Be carefull as some people are offering repaired modern cars for sale out of Japan as they are cheap but may end up costing you your car.

The rule is below so read into it dont take somebodys word for it.

A RAW would take all reasonable steps to avoid importing a crash damaged or corroded vehicle.

A RAW wont put up his bussiness to save you money.

In a nut shell they are saying dont bring in a damaged or repaired vehicle. I know of one complyier who knocked back a car as they were told by the importer it is a repaired vehicle but only minor damage. They knocked back the work and said unless you are 100% sure it is minor it will be at your cost. So the buyier went back to the broker who wouldnt sign a document that the car will pass the RAWS inspection then the importer went a bougt a straight as car to save the trouble.

Damaged Vehicles

Crash damage or corrosion may affect continued compliance with the ADRs. This is especially so in the case of the occupant protection ADRs 69, 72 and 73. It is not possible for a RAW to provide a reasonable level of assurance that a crash damaged or corroded vehicle, where the structural integrity of the vehicle has been affected, complies with all of the applicable ADRs. Therefore, it is not permissible for a RAW to fit a used import plate to such a vehicle.

Before commencing compliance work each vehicle must be inspected by the RAW to check for crash damage, damage repair or corrosion that may affect the structural integrity of the vehicle. Records of this inspection are to be retained by the RAW and be made available to VSS inspectors upon request. (Regulation 57)

Crash damaged or corroded vehicles where the structural integrity may be affected must be re-exported or destroyed. It is expected that a RAW would take all reasonable steps to avoid importing a crash damaged or corroded vehicle.

The criteria below must be used as a minimum when deciding if crash damage or corrosion is likely to affect the structural integrity of the vehicle.

q Underbody damage which results in the:

Ø crushing of floorpan stiffening members,

Ø splitting of seam welds or

Ø tearing of the metal

q Damage to rocker panels (or outer sill) which result in:

Ø Dents to a depth of more than 25 mm

Ø Creasing, distortion of the sill weld

q Distortion to longitudinal rails affecting the front and rear crush zones.

q Collision damage to steering or suspension components.

q Damage to the vehicle’s outer body panels, which affect the integrity of any of the seams or joints installed by the vehicle manufacturer.

q Corrosion (rust) which has resulted in perforation or flaking of the metal.

When checking the condition of the vehicle the following items need to be inspected but not necessarily in this order:

q Engine compartment

q Right side

q Luggage cargo compartment

q Left side

q Underbody or chassis frame

q Passenger compartment

Guest

Guest

Posted
Posted

I will always drive a import, Soarer loved it, 180 now that car is fun and RX7 sitting in showroom waiting for me to sell 180.

It is worth it and take advice from people that have nothing to do with the people you are buying off and dont rush.

I have personaly seen a couple of importers telling the truth to buyiers knowing that they wont sell a car to them, they just want to tell the truth, they have a heart beat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • hardsteppa
      R-chassis INNER tie rod torque spec?

      By hardsteppa · Posted

      Not sure if you're being serious? I, and all the car people i know, ALWAYS use a torque wrench for wheel nuts. I assumed any car person, apart from tyre centre monkeys with rattle gun in hand, would do it properly.  Anyway, no further reply from me on this unless legit discussion from OP or his query so, over to you, knock yerself out.
    • PranK
      Wheel refurb?

      By PranK · Posted

      I was wondering about this. I'll do some research.
    • Predator1
      Rb26 iron block limit

      By Predator1 · Posted

      Why not? Since mines been built, I've used low boost maybe 5 times.
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Yeah, so widen your search to any Nissan speedo first, then go wider if needed. I will say though, that there is a better than even chance that what I said first will likely come into play. They quite possibly won't come apart without damage. I tried to disassemble a stepper gauge that I wanted to repair. There was no way that needle was coming off the spindle, and I could not see how the spindle would come out of the mechanism behind. Assembled once, never to be disassembled, was my conclusion. Could be the same on the R34 cluster. Failing that - take the cluster to a workshop that specialises in automotive instrument work. There's usually at least one in every Australian city. They'll either be able to do it for you for small cost, or tell you it can't be done. It might be that "it can't be done" unless you follow some arcane procedure, including trickiness to glue it back together or something, that only experienced techs know.
    • GTSBoy
      R-chassis INNER tie rod torque spec?

      By GTSBoy · Posted

      Well, given that I, an engineer, almost never bring out the torque wrench to tighten up chassis bolts, despite fully knowing the theory, and instead rely on feel, which I happen to know is exactly how the majority of mechanics do things, should tell you the level of actual peril that exists from not achieving exactly 88 Nm of torque. How about if I just say then that 88Nm is at the lower end of the correct wheel nut torque range? Everyone knows how to tighten a wheel nut, right? And almost no-one ever brings out the torque wrench for that task
×
×
  • Create New...