Jump to content
SAU Community

Recommended Posts

Hey guys i just brought my first r32 gts-t i was wondering which turbo would be my best choice. it already has a gt35r on it an its a laggy as f*k it starts to make boost around 4300 an full boost around 4600.car has wolf3d, larger unkown injectors sard fuel reg.custom turbo manifold with external gate etc etc.After around 200-230kw.what would be an ideal turbo that makes boost around 3000? any thoughts would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/249380-gt35r-downsizing/
Share on other sites

Have you driven a car with that much? That turbo is rated for 300+ kws or so... that's a big drop down!

I have a VG30 turbo lieing around (slightly better then an RB25 turbo)... you could highflow it for around 220 - 230kws...

NYTSKY mate i was thinking along the lines of a gt30 when do they start to make boost?a lot of people on here seem to be using hks GT 2530. Mlr mate with the cam gears what sort of rpm do u think this would lower the boost range by? thanks

Not sure mate, I'm looking into this as I'm having the same thing going on with mine, rb25 with gt35, tuner recons it will drop between 250 to 500 rpm.

Not doing this though till next year when its going in for a rebuild so no answer on this for a while from me, sorry.

I'm sure someone on here could give you a definitive answer.

Not sure mate, I'm looking into this as I'm having the same thing going on with mine, rb25 with gt35, tuner recons it will drop between 250 to 500 rpm.

Not doing this though till next year when its going in for a rebuild so no answer on this for a while from me, sorry.

I'm sure someone on here could give you a definitive answer.

Yeah i will do some searches on that an thanks man.

Unbiased opinion.

GT3076R would be good choice

But if it was me I could not go past the Billet S56-GT3 with .63 A/R hot side.

The S56-GT3 specs are pretty dam good

The S56 compressor wheel has a 56mm inducer and 80mm Major + (ETT).

Turbine has an exducer of 56.6mm and a major of 65mm and is made of 713C Inconel

Compressor map

S56ETT.jpg

Turbine.

GT31.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Hey lads just finished tidying up a gtr a bought. Originally from Sydney now living in New Zealand 
    • Hi Guys, Looking for this piece if anyone can help out.   https://tfaspeed.com/products/nissan-skyline-r33-gtr-rear-trunk-finsher-panel
    • How did you go with your problem? End up fixing it. Have a y34 aswell vq30det
    • But if I smoke test 5th cylinder it’s all ok, no leaks  when I try with 2nd it’s leaking exhaust and intake, it doesn’t come from oil dip stick.    so maybe when car was running poorly, rich or sth. Spark plugs were black and covered in charcoal or sth lookalike. could potential contamination make valves not seal properly? is there also a possibility that rb’s don’t have equal performing cooling passages  meaning back of the engine will be hotter than front. Can this cause improper wear if engine was running under load for short time? Or carbon build up could just burnt from 4-6 and is still on 1-3?   I out of my head like really. Timing is as manual crank-exhaust 47, exhaust-intake 38 at this point I thinking about give it a try and make another 500-1000km and check if anything change, if not I will most likely disassemble engine head /or whole engine and send it back to rebuild. It’s killing me     
    • Thanks Duncan, I don't have a GTR these days mate. Gone soft..
×
×
  • Create New...