Jump to content
SAU Community

Recommended Posts

Oil is like PS3 games, every1 has a favourite, How I chose was to read as much as I could from testers, and looked at what race teams in Japan were using too.

As long as the oil is fully synthetic, you should be ok.

Just for the record I use Motul 8100 5W 40

Live on Gold Coast, temp gets to nearly 40 in summer and 0 in winter as I live in a valley. Its good stuff, bit pricey but worth it.

Just make sure Oil & Filter are changed every 5000k's-thats the true secret

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4325378
Share on other sites

i use motul 300v. :D

Dude you're rich :D

Motul 8100 5W40 here.

mines coming up soon too.. so I need to know what oil and oil filter to buy (stock engine ~ 50,000km)

You need 145A oil filter if your car was manufactured before 11/98. If you was after that you need Z442. They're both thread compatible but the Z442 is smaller and has finer filtration.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4331101
Share on other sites

if your car hasnt been run on fully synthetic for the last 100000kms or something along those lines, going fully synthetic wont really make too much of a difference now. Remember when half of these cars came out, fully synthetic oil wasnt out yet. I use castrol 5-30 fully synthetic which works for me, but every car is different and wether your engine is worked or not.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4331837
Share on other sites

I was reading something in Import Tuner magazine, talking about how this really popular engine building in the states looks after his race cars and his daily driver (a camaro). He was saying that shell full synthetic removes about 60% deposits from old motors in the first oil change. So it definately makes a difference even if you haven't run synthetic for it's entire engine life.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4331906
Share on other sites

ouchies,

well in my R33 GST-T i used,

Semi-synthetic Oils 'cause its a waste to throw hundreds in when your dumping it out every 5thou kms'

7.5/30 winter 'cooler weather, so wont loose its velocity as bad as summer

10/40 summer 'cause oil will be hotter, so need something that will maintain itself'

personally i found 7.5/30 too noisey in summer... because its so thin and is like piss water when hot...

and considering its an older car/engine (km's)... if its to thin it can get past the oil ring n you burn a little, not that you should notice it.

Link to comment
https://www.sau.com.au/forums/topic/249390-what-oil/#findComment-4333353
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I just got to work and skimmed through 61508 and 61511. I was surprised the CSA adopted both, but neither are enforced. To recap what I read, it states that in a perfect world, they should be segregated but they acknowledge that this is not industry standard and clearly mention that they allow mixing of safety and non-safety. 61511 also mentions software segregation like AB does in their safety PLC's.   Now if only I could go back to control, let alone safety over comms. In my current line of work, we're only allowed monitoring and basic control over comms. Everything critical must still be hard wired as much as possible. 
    • I've unfortunately never been as they're on the complete other side of the continent and another country that isn't currently letting us in as easily as they use to. I even heard their stop signs over there actually say "Stop" instead of "Arret". If I decided to trek the 48h drive, I wouldn't know when or where to stop haha. Whenever I order parts from UP Garage, I order from Japan as it's cheaper. Same with GKTech... oddly enough, it's cheaper shipped from Australia then it is the US.  UP Garage Japan operates their US leg though, unlike Tomei. If Tomei JPN had the power to close down Tomei USA, I'm sure it would be done in a day. They're two completely separate entities. Tomei JPN messed up somewhere originally agreeing to its creation and got sacked big time. 
    • I asked someone about this and he told me about the Audi 1.8T engine. But I think it would be difficult to swap
    • I don't know that machine specifically, but I'd personally go for something with a little more kick than 130amp. Around up to 180 would be good. At the 6mm range, you're really pushing the machine hard and don't have a long period you can run for with out needing to give it a rest. Lots of MIG machines come with a regulator and hose. A lot will come with a starter roll of wire too, but it isn't too expensive to buy. I'd recommend NOT buying a massive roll too, as you don't want it sitting around FOREVER in the machine between uses and potentially going to shit. For thin sheet metal, get a roll of 0.6mm if you're doing over 3mm and above, switch over to 0.8mm wire. Even by 2mm you'd probably really want to switch. As for gas battle, it's all swap and go style now. You'll pay a bottle deposit, and then X amount to swap for a full one. I think it's like $200 or $300 for a D Size bottle upfront as "deposit", and like $110 to $150 per swap. My D size CO2/argon bottle lasts a fair bit of welding on the MIG. And I run an E size bottle on the TIG. For DIY MIG, stick with a D size bottle. If you really start to get into a LOT of welding and doing it really regularly, then upgrade. If you're like most DIY car guys, one D bottle will last you 2 or 3 years easily. I think I've been on my current bottle about 5 years. It is starting to get low, but I've been smashing it a lot more the last 6 months.
    • SR20s came with cars like the Bluebird and Primera, but the RB20 never came. The ones in Turkey were either brought in specially or from abroad. That's why RBs aren't as common as SRs. And if a part breaks or I need to replace it when doing maintenance, it's harder to find parts for RBs.
×
×
  • Create New...