Jump to content
SAU Community

Iq3 Dash By Haltech/racepak

PSI Parts

By PSI Parts,
in Motorsport Discussion & Builds

 Share

Recommended Posts

DCIEVE Mentor

DCIEVE

Posted
Posted (edited)
Thanks. Have sent them an enquiry.

Edit:

Damn that was a quick response from modyourcar!

Was told you need a Haltech ECU for this dash.

Bummer!

If that's true (doubt it) then it applies only to the haltech version, but check out the racepak forums for ecu compatibility (adaptor modules etc). And search around for the cheapest place to buy them - normally direct from the US is best, but Intune in WA were selling them incredibly cheap (950 for display only) when a friend checked towards the start of the year.

Edited by DCIEVE
Link to comment
Share on other sites
BCM Newbie

BCM

Posted
Posted (edited)

You don't need a Haltech ECU for the IQ3s.

Racepak sell modules that translate between most aftermarket ECUs and the dash.

So they have modules for Motec, Autronic, AEM, Big Stuff, OEM Corvette ECUs, DFI, Haltech, MEFI, Pectel, FAST, XFI and some sort of generic CAN interface. Doesn't look like they do one for PowerFC at the moment. Worth speaking to them though because they are very pro-active if they see a marketing opportunity.

There are also two versions of the dash. A full logging version and another that just displays things. The one linked in this thread on modyourcar is the display only version. Either versions can be hooked up to any ECU that has an interface. Or you can run them without any ECU interface at all. Just don't have as much to display or log.

There is a guy called Mike Runge here in Australia who is stocking them. I'll try and pull his email off of my laptop if I can get it to work after running it over this afternoon with the Evo :( Bizarrely enough whilst pulling out the Autronic interface from my IQ3 setup to lend to a fellow IQ3 user whose interface had died and is entered in Targa West next weekend.

Edited by BCM
Link to comment
Share on other sites
BCM Newbie

BCM

Posted
Posted (edited)
Sounds good. So on top of the dash you just needed the interface module so it works with the ecu (I have an sm4 as well), and the usm module for additional inputs (oil/water temp, oil pressure etc).

Correct. System works like shown below. Excuse crap paint pic.

620335559_HFkgr-L.jpg

Edited by BCM
Link to comment
Share on other sites
  • 5 months later...
ENGINR Apprentice

ENGINR

Posted
Posted (edited)

Hi guys - am wanting to revive an old thread so as to enquire who has purchased one of the Racepak IQ3 logger dash units and if so, from where. I have only started exploring this avenue of modification so am hoping to get some good pointers as to where to start looking and who has provided good/bad experiences in the buying/selling process.

I am wanting to purchase and install the IQ3 dash, Autronic SM4 interface and USM 4 channel interface unit for my 4G63 powered Lancer Coupe.

Any assistance would be greatly appreciated.

Edited by ENGINR
Link to comment
Share on other sites
sav man Grand Master

sav man

Posted
Posted (edited)

i've got a haltech/racepak dash. waiting to put it in the car atm. the racetek site has a price list which is pretty good.

$375 USD for the Autronic modual

$1395 USD for the logger dash

$175 USD for UMD

$1945 USD total

or

$2242AUD + postage.

i'm not not sure if the Haltech vnet module will work with the Autronic, i don't see why it wouldn't, as they both run the CAN interface, but might as well contact a Haltech dealer and find out, cause i think they are slitly cheaper from Haltech ATM.

Edited by sav man
Link to comment
Share on other sites
sav man Grand Master

sav man

Posted
Posted

I was looking at the states, was quoted $200 USD for postage though. My local tuner is a Haltech distorbuter, so I got it through him.

A few tuning companies are onselling the IQ3 now, i know Tomie are selling them (at a 11ty% price hike)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      My 6 Point FIA harness have arrived (kinda). There was a mix up from the supplier and I ended up with 3" set rather than the 2" set. I contacted them and their customer service was top notch. It is being resolved and 2" ones will be on their way to be soon but in the mean time I was able to at least mock them up in the car to see the vibes. Need to organise some fixed back seats so i can actually use them as a 6 point. I am leaning towards the Velo Podium II XLs as I like the look of the bolstering compared to the GP90 XL or GPT2. The side and thigh bolstering on the GP90/GPT feels less that my existing Bride Digo R recliner. Velo Podium II XL Velo GP90 XL Velo GPT2 
    • Prof_Finesser
      R32 RB25 head and block

      By Prof_Finesser · Posted

      Yea I know the wiring would be fine just want to use I got. This was my first built engine and it blowing got me beat down just want to have it running right again but hopefully I can find a non vct head so I don’t have to do any of this lol. 
    • bcozican
      R32 Gtst - Track Car

      By bcozican · Posted

      Recently did the Perth Festival of Speed - and basically what we thought might be an average event turned out to be absolutely awesome they bought Mad Mike and Xtreme over and was good to see Perth get, support and produce something so good - 24,000 people in two days      It was nice to have it close to home for once yet have my whole crew there to run the car properly     Xtreme got the tin top laps record with 51.57    I hadnt done a hot lap on the home track for 20 months and finally everything clicked and dropped 4 secs off PB and did a 53.29 which is 3rd fastest tin top ever around that track. only 1.3 tenths behind 2nd so should eat that up soon... can I get Xtremes time - its not out of the question   Alll the blaa blaa's in the world but if I can replicate even close to that situation on other tracks will be able to make an impact     We got asked to do the hill climb to put on a show which in reality is just using some chicanes and the short track at barbs but good fun... launch control was put in and won the Pro class in that also.     Car needs some attention after being on it around Australia for last few months moreso the carbon underbody work and just a run through and clean up everything else seems to have held up good enough. Would like ,to take some weight out but that requires alot of effort 😁   Also waiting on new rules for WTAC and have some decisions to be made there and prob some minor modifications to suit pending class changes. Will see...   Divided on whether to go hard for one more year or chill out re: events this coming year prob more on the go hard and see if I can get improvements in times. If I didnt have so travel so far it would be less of an issue but I do so hmmm...   Also because build thread - gone to flappy paddles and a gearing change with a drop gear. It was becoming apparent that there were situations where I really needed to be hanging onto the wheel with both hands yet had to change gears and was getting a little sketchy and / or I just didnt change gears and delt with it and also 5th gear at 10,000 rpm is 290 kmph so I havent been using 6th as did 282 at WTAC and 274 in Perth drop gear will change to 6th being 300 at 10,000 rpm should also get a touch more acceleration speed    
    • GTSBoy
      R32 RB25 head and block

      By GTSBoy · Posted

      No, not really. Except that there are newer, better cam options that don't date back to the 90s. I was under the impression that you couldn't use VCT with them, which is why I said to get rid of them. If you can't/won't use VCT because of what you listed above, that's another matter. Although I would have said the wiring aspect of it was something that you should just suck up and do, as it isn't hard. Getting an actuator for the cam gear will possibly be expensive. I still say VCT is for the win. There's a reason HKS makes money selling it for 26s.
    • Prof_Finesser
      R32 RB25 head and block

      By Prof_Finesser · Posted

      Is there something wrong with using tomei?  I’ve heard the tomei usa are fake parts. Reason why I don’t want to make vct work is one gotta make a plug for the solenoid get the vct cam gear. I rather just use the stuff I already have. I made 450 on 17psi full boost at 4K. I’m satisfied with that it’s a street car and sometimes hit the track for drift. If I’m really wanting to decrease the lag I’ll go to a smaller rear housing as I have an extra or even cam gears. 
×
×
  • Create New...