Jump to content
SAU Community

Recommended Posts

ok so i'll tell the story later but i got done good in mascot last ngiht....it was quite funny all up.

anyway one of my 5 defects is that my battery is not in a 'sealed yet vented enclusure'!

does anyone know what that is and is it standard for a R33??? my car never got complied with a box for the bettery in the boot???

also what is the rolling diameter of a stock R33 Gtst's wheels?

more details of this funny story to come...

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/
Share on other sites

the usual "if in doubt hand it out" mentality was obviously in play here.

what he is saying is this

battery's which aren't sealed units that are mounted i the car need to be in a box which vents outside the car

which your car obviously doesn't have because R33s come with the battery in the boot but not in a box

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328234
Share on other sites

yeah see my problem here is i was taken as part of an 'operation' to an RTA inspection station! this was done at 8pm and i went to this place where thewre was like 20 dudes all sitting around....clearly nothing better to do on a friday night...lol

any my defects were issued by the RTA and then i copped fines from the copper...

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328236
Share on other sites

yes five fines! $81 each!

1. battery not in box or vented to atmosphere

2. ground clearence (by 1mm on resonator of exhaust, car is 110mm high)

3. stealth fx BOV (set to recirculate, but doenst matter)

4. turbo timer

5. rim size (this is bullshit as its all about rolling diametre size and not rim size...tyreplacrd says 17", i have 19")

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328242
Share on other sites

you can fight em in court if you think its worth it

1 is bullshit we know that for sure

2 sounds about right, cause has to be 100mm from the lowest point which seems to be your exhaust

3 gonna have to cop that one

4 turbo timer, i dont know the legality on this

5 you car came stock with 16s AFAIK you have to measure the stock rolling diameter and then measure your current one, is its no more that 15mm more your in the clear.

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328255
Share on other sites

5 you car came stock with 16s AFAIK you have to measure the stock rolling diameter and then measure your current one, is its no more that 15mm more your in the clear.

I thought there was another rule that for the rim that you can only go 25mm wider and 25mm more in diameter. So if your car came with 16x8, then you can go as far as 17x9 (unless you get it engineered of course).

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328432
Share on other sites

Don't you have that plastic thing in the boot which blocks your battery from view? Then put the standard strut brace infront of that as well, your timer is illegal unless wires to hand brake , just relocate it to a more hidden area, I got this single din cover with a flip lid which hides my profec ebc and timer + edfc and never had anyone inspect there

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328702
Share on other sites

one more thing you either got ripped off or the cop was a stupid sod, it should be 81 in total I got defected for 3 things once and the total was $81

Incorrect. You can receive up to 5 infringement notices. Every defect can bedealt with individually

oh and also with regards to the 25mm rim rule in NSW there is no such thing.

This is directly quoted from the RTA

Wheels up to 26mm wider than the largest optional wheel recommended by the vehicle manufacturer for the

vehicle can be fitted without the need to notify the RTA.

The outside diameter of the wheel and tyre combination must be no more than 15mm over the largest diameter

wheel and tyre combination specified for the vehicle and not more than 15mm below the smallest diameter wheel

and tyre combination specified for the vehicle.

Link to comment
https://www.sau.com.au/forums/topic/249628-defect-help/#findComment-4328828
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani Refurbed astra pump thats the cover for it in the boot I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • I've been building a 26/30 for a few years now. I've had the head built with all the good stuff. I had a 32 gtr but blew it up and yes its all going into a vl but im looking for some advice from some RB nuts on pros and cons on putting a 26 head on a 30 bottom end is it worth it Works are as follows Head -Extensive porting 1mm oversized supertech valves Supertech double springs Supertech valve guides Supertech titanium retainers Tomei solid lifters Tomei 270 x 10.25 cams Head drain Bottom end series 2 rb30 block Cp ceramic coated pistons Eagle rods Romac balancer Oil restrictions  O ringed blah blah spent a fortune And will get a girdle because the 30s arent used to handling that much rpm Nitto billet oil pump Hypertune plenum 6boost mani I did have a precision 6262 but sold it because drag car life. Currently building the ass end full 4 link floater rear end with a 2 speed  But the dilemma i have is my mate rekens I should just stick with the 30 head for reliability. Has any one had any issues with mounting the 26 head ie compression blowing gaskets etc. Just looking for some advice from people who have gone down this route. Here's some photos. Blew the oil pump in the gtr and decided to rip the motor out at the time and do a full build only to find it had been a repairable write off so went down this path.     
    • lol no cats running str pipes … might put the high flow back on but I suspect it might effect my ignition timing a bit. 
    • That looks a bit like yellowing to me. If the rear bar was looking like that from rich idle, I'd ask the question, do you have a catalytic converter fitted, and fully working?
    • Oh yeah gets really bad down here. I’ll have to upgrade the heater and wind screen wipers as well for optimal performance.
×
×
  • Create New...