Jump to content
SAU Community

R32 Gtr Cams + Buckets, 32 Coupe Gts-t Wrecking

Dabro
 Share

Recommended Posts

Dabro Collaborator

Dabro

Posted
Posted

32 GTR Parts

Cams and Buckets good condition $350

AFM x2 Were working sweet when removed $50 each

Wrecking damaged R32 GTS-T Coupe. Keeping running gear for GTS conversion, most other parts available.

PM for what you need and I will try to help.

Complete RB25-DE engine with flywheel and low Km's clutch $1250. Runs sweet, doesnt smoke. Approx 170,000km's Has weaping welsh

plug under exhaust manifold that needs changing. Non VVT. No injectors or rail.

Bare RB20DET head $100

RB20DET bottom end in Pieces, has one melted piston. $200 Crank and cylinder bores ok from memory.

Ignition crank angle sensor $80

PM any questions

Thanks

Perrin

Link to comment
Share on other sites
Dabro Collaborator

Dabro

Posted
  • Author
Posted

All,

I am going away for a week from tomorrow. Answer to all questions and PM's so far is yes everthing asked for is available.except I'm not to sure on what the projector headlights are. These have a rectangular inner light and a round style outer light. It is a 94 model car if that helps.

I will answer all PM's when I get back and if you are still interested I can start stripping parts on the weekend of the 17-18th

Cheers

Perrin

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • rbs30
      RB gearbox options

      By rbs30 · Posted

      Newcastle NSW
    • ck_chino
      Nismo copper mix twin “pull” pedal height engagement

      By ck_chino · Posted

      Installed  Nismo coppermix twin competition spec last year in my bnr32 with pull trans with Oem slave cylinder. The point at where the clutch disengages/enages is right at the top of the clutch pedal, meaning I barely have to push the pedal down for the clutch to be disengaged.  You guys that have the same combo are you experiencing this high pedal bite point??   Secondly I’d like to have the disengagement point lower meaning I have to push the pedal more(further not effort)for it to be disengaged.  I’m thinking to use a Nismo big operating cylinder(bigger bore at 13/16 vs Oem 3/4) which will require more pedal stroke to get the equivalent movement at the clutch fork. But I see Nismo web site says not to mix these 2 as the Nismo big operating cylinder doesn’t have enough stroke to disengage??? Any folks run both the coppermix twin pull with Nismo cylinder??    Thanks in advance for the replies but prefer only guys with pull clutches to respond. thanks     
    • Watermouse
      RB gearbox options

      By Watermouse · Posted

      Any chance u could let us know where your based ?
    • rbs30
      RB gearbox options

      By rbs30 · Posted

      That’s a great deal and I would jump on it if you were closer. Melbourne is a bit of a hike for me though unfortunately 
    • soviet_merlin
      Fake ARP bolts?

      By soviet_merlin · Posted

      I wonder if there is much to tell without knowing where the bolts where bought from. If it comes from Amazon or similar all bets are off. Can't trust them. And I fear not everybody knows that. Wasn't it @TurboTapin who ended up with the fake fuel lines recently? The submersible ones which very much weren't submersible at all. It kind of applies to everything nowadays. Doesn't matter if it's hardware or electronics. The fancy camera might have internals swapped out for cheap knockoffs. The hard drive will report a certain size but not actually be able to write it all. Shit like that. A bit depressing but the reality is you really have to be weary of where and how you buy stuff
×
×
  • Create New...