Jump to content
SAU Community

Recommended Posts

is that 3rd gear paul? awesome results mate...all that bullcrap to support your fuel system LOOOOOL

Nah mate second.

at 8000 RPM with 4.111 diffs (stock)

1st = 87

2nd = 138

3rd = 190

4th = stock (1:1)

5th is shorter at 290 but i stuck with the stock gear which goes to 310

Another problem is the CAS. Both Steve and I have developed Crank Angle Sensor noise above a certain RPM.... So basically you cant be 100% accurate with the timing up in the rev range. I was warned about this before this tune and was hoping it wouldnt come up.... but it did. Now in all my years of scratching around on SAU and the pommie forum I have never seen a thread discussing this issue. Has anyone else come across this and if so why isnt it common knowledge!?!?! There is a fix... a balancer trigger... but thats expensive and to be honest I really cant be arsed........ thats what I said 2 years ago! haha

Yavuz says it's from the belt flopping or shaking at such high rpm. We are only talking 7000rpm plus. So for most people it doesn't matter, bit the people in this thread clearly aren't "most" people :action-smiley-069:

Yes it's a common problem but usually easily fixed by fitting a dual pulse disc in the CAS.

Don't remember it being more than $100 and when your engine blows you'll kick yourself. Either that or you'll see your timing walk around 10-15 degrees in the top end and that'll be enough for you to make the decision to fix it

Another problem is the CAS. Both Steve and I have developed Crank Angle Sensor noise above a certain RPM.... So basically you cant be 100% accurate with the timing up in the rev range. I was warned about this before this tune and was hoping it wouldnt come up.... but it did. Now in all my years of scratching around on SAU and the pommie forum I have never seen a thread discussing this issue. Has anyone else come across this and if so why isnt it common knowledge!?!?! There is a fix... a balancer trigger... but thats expensive and to be honest I really cant be arsed........ thats what I said 2 years ago! haha

Paul it's discussed in this thread from GTROC

http://www.gtr.co.uk/forum/52458-rb30-engi...ts-pics-12.html

Starts on page 12.

Mark

Yes it's a common problem but usually easily fixed by fitting a dual pulse disc in the CAS.

Don't remember it being more than $100 and when your engine blows you'll kick yourself. Either that or you'll see your timing walk around 10-15 degrees in the top end and that'll be enough for you to make the decision to fix it

Would that be the same mod to the CAS that needs to be done to run an autronic known as a slipper disc?

What is it like driving a car that takes until 5k before the power really kicks hard? Is it annoying on the street or is there still plenty of meat below 5k? Looks like a solid 200kw at 4k, does it feel good at the lower revs?

Edited by Rolls

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • IMG_8641.mov     She doesn’t sound the best but starts with out using any gas now. I just ran some injector cleaner through her. started roughly the first time after adding it but gave it the beans slowly upto 4k, Must have cleaned a few cobwebs out. another step in the right direction for the sub
    • Sadly I can confirm if you are actually seeking to drift, you will quite easily spin up one wheel. Even if you're going in a straight line. I am not entirely sure of the metrics/terminology here but there's only a certain amount that the helical will actually spin both wheels. I've seen it on video with my own car where two lines of smoke switch over to just one after you really get in to it. Unlike with a clutch diff where you can keep your foot planted until the car regains grip, in my experience with the helical you want to be utilizing traction control allowing LIMITED slip or lifting (partially) when you start to spin up both tyres with a Nissan helical. Which makes them pretty sub optimal for drifting duty. That said... this is probably a helical on numbers alone. Just put the Kazz in
    • Let's just fix the problem by f**king the rest of the gearbox.
    • Unlikely, as per Greg's post. This is not helical diff behaviour unless one wheel is up off the ground. Shimming what? You don't "shim" a mechanical LSD. Probably not in the sense that you have heard of people "shimming" a diff. And the process that Nissan f**kwits call "shimming" a diff involves super-preloading a VLSD cartridge against the side of the diff to create a friction/wear point (in a place that it wasn't supposed to have one) to make the sloppy, useless, viscous diff into a hybrid viscous/mech abortion. In case it isn't clear, I consider the process to be stupid. Nike.
    • How much does the shifter move when the car is in gear with the engine off? If it is more than about 1cm you need to replace your shifter bush. Your shifts will just get crunchier, not faster, with a short shifter unless you also rebuild the whole box
×
×
  • Create New...