Jump to content
SAU Community

Recommended Posts

We only used two sets, both times the car wouldn't start. We had to run them through the injector bath twice before they came up good.

We had the same with a Bosch injector once also. That's why we clean all injectors before use now. They aren't bad injectors. Not a single injector on this planet can be cleaned and flowed, then sit for a month and still have its company guarantee its perfection.

We've never had lean out issues with the pencil type 1600's.

Any time we've had an injector issue with a Bosch injector (ID's included) they were fixed with a clean so we never had to return any.

Yep that's correct ID had a issue with a certin type of after flow matching lube that caused the batch problems. I know FIC and ID pulled the 1600's from there lineup cause of the leaning issue..

Dan, where did you get the ID"s from? plenty of people sell bog standard bosch ones as ID's

The ID's were purchased directly from Injector dynamics both times by my customers. They came with the ID spec and flow sheet also.

There are also no difference between the ID's and the Bosch injectors except for the fact ID apparently dead time test their injectors and Bosch don't.

Bosch are still flow matched and flow the same.

I don't see the point in paying extra for the same product. We have seen the spray pattern on both and cannot tell the difference

Just gasket on with nothing ye? Im sorry i know its a stupid question but its my first time

Yep, the gasket provided is all you need.

And I disagree with Marko, there are stupid questions....but yours was not one of them. I just couldn't resist the temptation to be idiotic

There are stupid Q's OK but it would even stupider to put that engine together then realise wtf I should have asked about that sealer (definitely not taking a dig at u daniel after helping me with that nugget white gtr u inspected for me at no fee last year :))

Anyone in here know of a place to get the push in fittings for RB26 cam covers with a 90 degree outlet?

NOT a straight then add a Speedflow 90 degree bend - that wont fit. Needs to be the same fitting that goes into the cam cover that's got the bend in it

I just want to know a couple things from you 400kw guys i wana know,

What sumps you guys are using if in melb where u got it from size cost and if from out of melb cost of freight

Can the std intake piping and cooler support 400kw ? Coz i wana try keep it for now cant afford it,

Std exhaust manifold port matched to gasket will it flow 400?

Cheers

Can the std intake piping and cooler support 400kw ? Coz i wana try keep it for now cant afford it,

Std exhaust manifold port matched to gasket will it flow 400?

Cheers

Standard intake piping as in the pipes from airbox to turbo's and the 'twin turbo pipe'? If so then yes

Exhaust manifolds are a yes also.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It's interesting seeing everyone talk about what level of risk they are happy to tolerate.  Building a GTR always has a level of risk, you could be that lucky guy that drops 20k on the engine build alone and still has the thing go pop on the dyno. Life is fun like that.  The way I see it, the thing is a toy to be enjoyed. I'd be happy to turn up the power on stock motor and limit the risk with sensible tuning and engine protection. If it still goes pop, it is what it is. The car isn't a daily driver so it can happily sit while a plan is made to sort it out.  Given this thing will be a street car only, I really feel it's worth the (relatively small if managed well) risk to turn the power up to around 350KW on e85.  I don't think anyone getting into the skyline game now is doing it out of logic. Surely it is a purely emotional decision so I'm not sure how important it is to think about the engine build logically. The heart wants what it wants.  @joshuaho96 little note for Josh, I run my 525 pump flat out all the time and through the factory lines without any issues. (excluding the melting connectors, that's sorted now. we'll pretend it never happened lol)
    • But the Nexus S3 is very expensive and won't be as purpose-built for the application as a separate electronic boost controller :^) More seriously my pet issue here would be that the Walbro 525 running at 100% duty cycle is going to require more FPR than the stock setup can handle. I'm also pretty sure from what I've seen elsewhere you might want to slow down the pump regardless unless you're going to come up with some way of upsizing the fuel lines coming from the fuel tank. Factory 8mm fuel line doesn't actually flow very much if you want to keep pressure drop down between the fuel pump outlet and FPR. If you really want to "keep it simple" I would run only as much pump as you need and source a fuel pump controller to slow down the pump in the vain hope of being able to run stock-style FPRs which are pretty dinky. Or just use the HICAS lines and it should be mostly fine. OP should also really think hard about what profile they'd want out of the turbo. My pet choice here would be the G1 profile rather than anything higher power but YMMV. I already think ~stock turbo lag is pretty bad so I don't want to make it worse. In "gentle canyon cruising" I found that I spent a lot of time around 4-4.5k RPM. I also recommend DIYing labor if you're detail-oriented enough. Costs are high for labor + if you do it yourself you can be your own quality control.
    • GTSBoy is again on the money. My actual advice? Sell the car. (really). For what it's worth as is, you can sidegrade into something much better. If you care about function then this is the actual move. If you want a Skyline to perform, set aside about $100K to do it. This is NOT a typo. You will see right away these are two very different mindsets. Realistically we're talking full restomod for any Skyline still kicking around. Have an honest think about which one you are.. and what you want to do, and how much you want to invest in this (with no return).
    • I promise there will be no chance of replacing the rad support....  It is barely twisted and it's way more likely to just be driven around with a slightly twisty support. As long as the headlight can be bolted in there then no harm no foul lol. The reo may need to be un-bent a little but truth be told if it all somewhat lines up and is hidden when the car is assembled the level of f**ks will be 0.0 
    • this thread delivers, once again Skyline owners, our cars spend more time off the road than on the road  
×
×
  • Create New...