Jump to content
SAU Community

Recommended Posts

Hey guys,

My mate is getting frustrated with his Airbag light staying on.

Has tried "factory resets" but the light stays.

He has the stock steering wheel and has taken the car to Nissan who found the error code "CRDRH".

Consult showed that the code is located in "other".

Doesn't seem to be affecting the driving of the car, but he would love to have it gone.

Any suggestions?

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/
Share on other sites

Nope.

Still there.

Any ideas?

Anyone??

..... Bueller???

Has he played around with the airbag? like has he installed the radio controller? Maybe plug in the back has come loose.

I have no idea really but I thought I would trow you a bone so you know we are trying to think of a solution.

Is this your mate with the $400 M35? If so, maybe think about the options fitted and where they may cause a problem to the airbag?

Cheers and good luck.

Andy

Edited by andy65b
Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4389510
Share on other sites

Has he played around with the airbag? like has he installed the radio controller? Maybe plug in the back has come loose.

I have no idea really but I thought I would trow you a bone so you know we are trying to think of a solution.

Is this your mate with the $400 M35? If so, maybe think about the options fitted and where they may cause a problem to the airbag?

Cheers and good luck.

Andy

Such a memory you have there sir!

Yes it is the $400 M35.

Can't really think of any aftermarket stuff installed that would have interfered with the airbag.

Maybe the entertainment system he has in there, or the Nismo dash could have effected it when installed.

The confusing bit is that it has disappeared in the past - although very briefly before it came back.

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4389596
Share on other sites

when i was doing trimming and the seats were removed from cars (mostly euros, but newer nissans are likely to be similar) and the car was then driven the airbag light would say on. the only way to get it turned off was to have a dealer reset the airbags via a diagnostic style tool. possibly the airbag plug under the seat has been unplugged or has come out??

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4389607
Share on other sites

I have exactly the same problem with my car... It came imported from Japan with an aftermarket steering wheel.. everything was fine still one night air bag light starting flashing and hasn't turned of since.. nothing had been touched so I'm not sure why it came on all of a sudden..

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4390013
Share on other sites

  • 1 month later...

Mine started flashing tonight and it won't go out :banana:

Wheel is stock, havn't had any collisions or anything.

Did anyone find a solution or a reason for the Airbag light to flash constantly? (comes on solid when you turn ignition on but once the engine is running it flashes).

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4498695
Share on other sites

Try this Stephen... worked for my mates car (although the light just came on again).

Turn the key to the on position and watch the airbag light. It should stay solid for 5-7 secs, and then turn off, and then start to flash.

To reset the light, you must turn the key to on, watch the airbag light stay solid for 5-7 secs and as soon as the airbag light turns off, turn the key to the off position (you have to turn the key to off before the airbag light starts to flash, or you must start over). You need to repeat this 5 times. Try to start the car, and hopefully the light will be reset

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4499171
Share on other sites

Try this Stephen... worked for my mates car (although the light just came on again).

Turn the key to the on position and watch the airbag light. It should stay solid for 5-7 secs, and then turn off, and then start to flash.

To reset the light, you must turn the key to on, watch the airbag light stay solid for 5-7 secs and as soon as the airbag light turns off, turn the key to the off position (you have to turn the key to off before the airbag light starts to flash, or you must start over). You need to repeat this 5 times. Try to start the car, and hopefully the light will be reset

I will give that a shot, thanks dude!

I don't know as of yet what the actual error code is for my particular problem. I just tacked it on to this conversation as it referred to M35 issues with the airbag instead of starting a whole new thread.

I've been driving most of the day so I've seen enough of my car for now lol. I will give it a go tomorrow morning though and if it doesn't gel I will take it to Hornsby Nissan and get them to check it out. I want to go and meet the guys and let them know they'll have a new customer for all things nissan (i've still got to get around to getting a new rear sunroof rubber fitted, it's on the back burner for now tho!).

Once again, thanks for the assitance. Even if it doesn't help me on this occasion it's in the thread now so other's might find it if they have airbag issues.

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4500276
Share on other sites

Further to my last email I did end up going for a quick drive afterall, and I tried the suggested method and the light has now gone out.

However, if there is an issue that needs my attention I'm sure it will come back on, that being the case I will go and get Hornsby Nissan to check it out a bit further.

Thanks again :D

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4500679
Share on other sites

  • 4 months later...

need a tool attached to it for a proper idea. common thing is the seat tensioners. also bea in mind that the controller used in those was the same as the local 350z and 02/03 versions had issues with the controllers.

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-4738106
Share on other sites

  • 7 months later...

Guys,

My airbag light was flashing and I found the solution on the net and it worked first go on my M35.

Turn the ignition to the "on" position. Watch the airbag light closely(it will be on solid) the split second it goes off(beggining to flash) turn the ignition off, count to 5. Turn back to "on" position and do the same another 2 times.

Next time you turn it to "on" position it will blink really slowly(diagnosing) Then switch off. Next time you turn it on it will be solid and then turn off completely.

Link to comment
https://www.sau.com.au/forums/topic/254024-airbag-light-on/#findComment-5141321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Most of the industry in North America either runs on Siemens or Allen Bradley. I have two redundant S7-1500's on my desk right next to me for simulation. Siemens has been losing ground though since Stuxnet, as cybersecurity is a big thing. In my line of work that is federally regulated, you must by law have a cybersecurity management program in place and its audited and inspected every so often.  I work with Emerson PLC's daily (RX3i's) and have done large biogas/refinery projects with their DCS's. Their PLC's are somewhat OK minus the way they do PLC redundancy (You have to download on both PLC's separately every time you make a change )  As for their DCS's... you'll be limited financially first before anything else stops you. Costs are exorbiant at roughly 10x what it would cost you to do with any other system (e.g AB PAC).  1990's, those suckers are brand new haha! Kraft-Heinz (An old client when I use to work for an ESP) still runs Siemens TI505 PLC's from the mid 80's. Ohh how I don't miss working with those... you could only do a certain number of online downloads until it's "Change" buffer would be full and you would then need to go offline to do a full download. There was no warning of when this was coming up and it generally would happen when you would go in at 2am to make changes before production -_-.     
    • Unfortunately, not only is that not the case, one of the main "Selling points" of safety over comms is they clearly state in writing that there's no need to segregate safety networks from non-safety networks. It always gets intermingled with everything else on an ICS/OT network. 
    • Hello. I have an a31 cefiro but since I am in Turkey we have a CA20S engine. I did some research. Then I found that I can swap with a ca18 but when I heard that it has the similar substructure as the s13. I thought I can swap with an sr20 because the sr20 was used with the s13. So can I easily swap the sr20 on my cefiro or is it difficult? 
    • I used to love stock take. I used to take f**k of a lot of stock. /Rodney Rude.
×
×
  • Create New...