Jump to content
SAU Community

Recommended Posts

plug ok? check and clean.

other wise get a multi meter and check for a curcuit on the wires that come to coil 6. if open curcuit then you have cut or problem in the wires

Yer the plug is ok not dirty or anything & i swappd it when i swapped the coil pack 2 make sure..yer il chek the wireing thanks..coud it b the injector? Prob not cos it come up with ignition system fault code but u never kno sometimes

Link to comment
https://www.sau.com.au/forums/topic/254665-runnen-on-5/#findComment-4396526
Share on other sites

if you had a noid light handy you could check the pulse.

feel if its ticking. unplug when running and listen for a change

Yer i hav checkd & have power going tru the coil on that cylinder same as all the others..i dont hav a noid light 2 check injector pulse n i cant really tell if its ticking jus by touching it & if i unplug it will jus b the same as unplugging the coil..missfire...coud it b something bad like burnt valve or something?..-but i dont think a injector problem or burnt valve wood log an ignition system code..or wood it?

Link to comment
https://www.sau.com.au/forums/topic/254665-runnen-on-5/#findComment-4399433
Share on other sites

Yer i hav checkd & have power going tru the coil on that cylinder same as all the others..i dont hav a noid light 2 check injector pulse n i cant really tell if its ticking jus by touching it & if i unplug it will jus b the same as unplugging the coil..missfire...coud it b something bad like burnt valve or something?..-but i dont think a injector problem or burnt valve wood log an ignition system code..or wood it?

Ar its ok dont panic the computer jus wasnt plugged in properly!dont kno why that make just no6 go bad ok thankr

Link to comment
https://www.sau.com.au/forums/topic/254665-runnen-on-5/#findComment-4399513
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • But it's much better to use a freedom unit that has four different possible meanings...
    • I would try messing with friction modifier to see if it smooths it out.  Just keep adding more until it stops chattering or grabbing quite so much. If you haven't changed the gear oil in a long time you may as well start there too in case that has anything to do with it. You might want to also verify the initial torque is set to the lowest setting too. Requires popping out one of the CV axles first but that's not too bad. Once you're sure the preload is set to the lowest you can try adding an ounce at a time of friction modifier until it feels right to you.
    • It is possibly 55 degrees for the Nismo version. I had a look through the manual and the stocker has a breakaway torque of 2.5 to 3.5kgm. Supposedly the Nismo LSD goes down to 5kgm when worn in but it is pretty grabby even with very little throttle. Worse when cold. So I guess you have three things. 1. Shims. 2 Friction plates 3. Cams Would think shims would be the easiest but Ive no clue how many tenths of a mm shim thickness change equals how many kgm torque. Also not sure if the Nismo friction plates are similar/different to stock or if they are the most of the source of the diff being angry. Think I can write off the Nismo rebuild kit for the standard diff as not being what I want.  
    • Yeah, it was a bit of confusion with me, I rang and asked if they had a boot for a soft top, and then the paint shop when they rang and were asked if it had a hard top on it, which it does, just not a PRHT....LOL Meh, whilst frustrating for all concerned it isn't a war stopper and should be a thing of the past in a week or two In other N/A related news, car is booked in at the end of the month for the cams, springs, retainers, harmonic balancer and retune  I might even pull the lazy arse card and get them to do a full service on it whilst it is there
×
×
  • Create New...