Jump to content
SAU Community

Recommended Posts

Hey everyone selling my R324 as I have another daily now, mods as follows

Engine

1993 rb20det manual

r33 series 2 turbo

3inch dump and front pipe

kakimoto cat back

extreme clutch

front mount cooler kit

HKS pod

turbotech boost controller

bosch 040 pump

Suspension

Tein HA coilovers front

Cusco coilovers rear

front struct brace

hicas lock bar

Exterior

R34 front end conversion

R34 headlights

R34 FRP vented bonnet

wide front guards

R32 GTR rear quarters

origin mirrors

Grenade GX01 rims 18x9 +30 all round with 30mm bolt ons all round

Interior

R32 GTR dash cluster

momo wheel

shift knob

apexi boost gauge

apexi turbo timer

Asking $14,500 ono ring if your genuinely interested on 0401 483 906 located in Adelaide thanks Chris

post-31172-1233375359_thumb.jpg

post-31172-1233375411_thumb.jpg

post-31172-1233375459_thumb.jpg

post-31172-1233375511_thumb.jpg

post-31172-1233375563_thumb.jpg

post-31172-1233375606_thumb.jpg

Edited by d1a31
  • 2 weeks later...

ive seen this kit on ebay but it has side skirts and rear bar too, and i was thinking of doing it to my 32 so i culd try get more $$$ because the R32/4 is probs the best looking 34 around... but if your struggling to get 14k i think that just puts me off the idea!

great looking car though good luck with the sale

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
    • What HVAC actuator is under the steering wheel? Do you mean on the RHS of the centre console, immediately to the left of your shin? If so, then yes, it is probably that one, because that is the mode door actuator, and from what I know, it's still a pain in the arse to replace. I don't know about whole dash out, but you certainly have to rip into the centre console section. I don't know if it's covered in the workshop manual, as I haven't spent much time looking at those parts of it. (and by "the workshop manual, I mean the R32 GTR one, which is the most comprehensive one we have, and it should be similar enough between that and later cars to serve as a guide).
    • ...oops. forgot the TCU end...
    • No I got mine from a friend that had fabricated one … but I had to fit it to my setup which was a hks turbo setup. His was a Garrett -7. So one of my turbos was not a flange for one side … then I had a leak in the welds I had to find a weld shut … in the end the setup was decent priced but I spent a lot to get it fitted. A couple companies I checked would make it but you’re talking 7-9k aud with titanium. No joke mine was 6-7k even second hand after I had to fit it in Hong Kong … labour is expensive here. 
    • I'd just like to restate that I don't think anyone here is actually hating I recently sold a car part to a guy who was building a forged auto R34, with MV stall and aiming at ~450kw. I told him that I'm him, from the future and to stop after it explodes once. I told him I knew he won't listen the first time, and that's fine. But if my predictions do come true - Change direction faster than I did. I also said it's probably no coincidence that the dyno plot of a reliable turbo engine starts to look a lot like a N/A motor. :p
×
×
  • Create New...