Jump to content
SAU Community

Recommended Posts

this may be a very silly question but i am going to ask away any ways.... when is it time to get a engine rebuild or a new motor all together like how many kms? down the road my R34 is pushing 264,000 kms Dam that Melbourne trip and back to Perth from Geraldton was fun........ haha :D

I just put in New Spark Plugs and coil pack and my nasty Busted WRX Sounding motor is sounding way better now and not a WARNING light to be seen :):P:cool::D:geek:

So the question is how many kms before a new motor is needed?

Edited by DiNoBoNeS
Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/
Share on other sites

until it dies

depends how its been looked after

better = longer

no real number, lots of taxis run around with 600,000kms+

but they leave there cars on all the time and service very often

Tops thanks mate i try and look after her and do the right things i work as a photographer and i leave it running when i am shooting I am only with the guy/gal for like 4 minutes so no need to turn it off and on all the dam time... just was thinking if there was a kms number to do it or if it was the case of wait to it go hehe she is running strong and i do not think it will be for a while i can not wait for 300,000kms.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400195
Share on other sites

when it gets low compression, or has a fair bit of leakage.

leaving a car idling is not ideal either, the fuel isn't burnt correctly, and runs down the side of the bore, washing off the oil with it, and contaminating the oil.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400198
Share on other sites

your car will get hot if its just sitting there idling

best to just let it run for a minute or 2 then turn it off

rebuild it when it pops...

your car gets hot just idleing?

i dare say keeping it running > on and off all the time

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400429
Share on other sites

your car gets hot just idleing?

i dare say keeping it running > on and off all the time

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400446
Share on other sites

yep.. the only time we realised we hadn't plugged my mates thermo fans back in, was when we pulled into the macca's drive though, and it started to get hot.

most fans will stop, or slow down when the car is moving.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400449
Share on other sites

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

That's pretty hot dude.. highest I've ever seen on my 30 is 104deg and that was after a couple of big smokey burnouts on a 40deg day!

FYI boiling point is around 110-115deg.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400565
Share on other sites

yeh, if you had a digital temp gauge (i use my pfc hand controller) you would see

if your not driving and having air blowing through your cooler etc your car actually heats up at idle

not much but for example

my car usually operates at around 80-82 degrees

i sat in the car park and ate maccas with the air con on one hot day and the temp got up to 105 degrees and went back down after i started driving again

the day and air con did play a part so the temp rise isnt usually as big

best to turn it off..

If your car is getting hotter when its idling then something is stuffed. When temps start to rise a bit the fan is suppose to kick in to pull air through and keep temps steady.

My temps don't rise one bit no matter if I'm moving or not. Sits on 73 deg all the time (PFC hand controller and new watter temp sensor). Car also runs an N1 watter pump which doesn't flow as much watter at idle as a normal watter pump and still no issues at all

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4400819
Share on other sites

95% of engine wear happens when the engine is cold. Thats why taxis engines start to go at 1,000,000kms, and trucks get their engines rebuilt when they clock back to 0 only because they can. I've worked on trucks with over 500,000kms with engines that are fine, and cars that have bearing noise at just over 200,00kms.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4401253
Share on other sites

If your car is getting hotter when its idling then something is stuffed. When temps start to rise a bit the fan is suppose to kick in to pull air through and keep temps steady.

thats only if you have thermo fans on your car

belt driven fans are constantly working and engine temp SHOULD co up slightly if not moving due to less air movement through the core

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4402123
Share on other sites

(feel free to correct me people)

Oil is a major factor in engine wear.

your engine would run dry for 2 seconds before the cold oil is pumped up to the valves and while the oil is cold its not flowing easily.

I've seen inventions for pre-heating oil sumps before starting, and i'm sure someone will have invented a oil primer.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4403775
Share on other sites

actually the fans on RB's are clutched, they apparently stop moving at higher speeds.

but yes, they are constantly spinning at idle

They don't stop spinning at high rpm, the clutch is there so that the fan isn't spinning at full engine speed at high rpm.

As for oiling, there are products out there that retain oil pressure in a container so that the instant you flick the key, it squirts the pressurised oil through the system immediately prior to startup.

Link to comment
https://www.sau.com.au/forums/topic/255010-been-thinking/#findComment-4404321
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
    • One way of putting the fuel surge idea to rest, is that even when in neutral/clutch in or free revving it still has the same issue, it can’t even get to limiter (7800) so to me that says it can’t be g force, I’m not trying to argue I just want to find the f&$king issue 😡
×
×
  • Create New...