Jump to content
SAU Community

Recommended Posts

Well long story short. This lady hit my car. Not alot of damage but they did something to the Air conditioner.

They replaced the fan and took the radiator out.

Anyhow I had the car back for like 3 days. And on my way home from work on like a 40 degree day. It started pissing

smoke out from under the bonnet, I though it was on fire for a second. So i pulled over and popped the bonnet and

the was gas pissing out of that silver container that holds the gas i think. So i wiggled something on top of the unit and it stopped.

So i am taking the car back to the workshop tomorrow to get fixed. I just need some info on how the aircon works in a 1996 R33 gtst.

I have read a few topics.

What sort of gas should really be used for my car?

Could have they put the wrong gas in the car after the repair?

because i read that some gases eat the seals.

I dont think they changed the gas over when it got imported to australia.

Link to comment
https://www.sau.com.au/forums/topic/255094-air-conditioner-advise/
Share on other sites

From factory they use R12

Legally you can only use R134a gas in australia as R12 is ozone depeleting gas.

The leak will be most likely from a cut o-ring. Get them to make sure the whole system is leak free and has compatible o-rings. Your right you are supposed to change the o-rings when retrofitting to suit R134a gas. R12 o-rings are black whereas R134a o-rings are green. More often than not they arent changed and wont always cause an issue. By the sounds of it upon re-assembly they have damaged an o-ring or a fitting and thats where your leak is. A leak is often noticable by a greasy stain around a join in pipes/hoses.

Good luck,

Deren

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If doing that ^, I'd take the idle up valve out and plug the hole in the pump.
    • You can try capping the power steering idle up valve at both ends if it's old. The valve and the intake manifold. That is something that is known to fail in Toyotas with age and it will suck power steering fluid into the intake and burn it in the engine which can cause issues. Then bleed it again with engine off first. Do like 30+ lock to lock turns with the front wheels off the ground.
    • Hi Brent, I am wondering if you ever worked this out? I have upgraded this unit to a newer one and everything works bar the reverse camera, so i really want to know what plugs are what so I can patch the camera through. many thanks in advance Mike
    • Once you have to get up in the morning and be useful, you suddenly value sleep it turns out :p
    • Update:   smoke test all pipes no issues cleaned reservoir   fluid put in ( dexron 3 atf)   steering turn side to side and could hearing  gurgling from steering rack which I assumed was air lock, opened one of the steering rack connections and could see loads of air getting pushed out( not sure if you meant to do that / whether it will re introduce air into system)   anyways, loads of side to side sound was gone. Turned car on, pump was slightly ( barely) wining so turned side to side few more turns and fluid level when car on was almost none in resorvoir which I guess is normal if car is one. Turned car of and fluid was gushing out. Almost 200-300cc was pushed out. Repeated engine off side to side followed  by engine on and same result       going mad now. It seems system is either sucking air in whilst on or there is tons of air which I am not giving it enough time to bleed. Thoughts?   would it work like brake caliper if I open steering rack copper pipes and let gravity pull all air out?   or maybe have a restriction somewhere? What is the red circled item, could that be blocked? It i
×
×
  • Create New...