Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

Do you happen to have the fuel dampener? The one that sits on the drivers guard on the return line. Basically sits next to the fuel filter, looks like a fuel regulator, but has no vacuum line going to it, just a fuel in, and fuel out?

I need that and the bracket holding it to the guard if you have it?

PM me back if you do.

  • 3 weeks later...
Hi, im listing a few R33 that i need to sell ASAP. They are priced very cheap to sell fast. Located in Campbelltown-Sydney.

Engine Bay + Suspension:

A/C Compressor + Lines up to firewall $45

Power Steering Rack $75

Power Steering Pump $45

Brake booster $50

Master cylinder $45

slave cylinder $40

Wiper motor $35

Bonnet lock assembly + supporting bracket $25

Bonnet hinges $10 each

Washer Bottle $15

Coolant over flow Bottle $15

Charcoal canister $15

Front Wheel arch covers $5 each

Front calipers $35 each

Rear calipers $20 each

Front hub assembly $50 each

Exterior:

Bonnet (small dent in middle, grey in colour) $50

Passenger door $40

Boot lid + flat spoiler $40

Left Guard $35

R/H Tail light $40

Headlights (side bracket broken on both to accomadate for 400r Bar) $10 each

Guard indicators-amber $10 each

Wipers $5 each

Driver and passenger windows $30 each

Exterior door handes $15 each

Antenna + motor $25

Petrol lid/cover $20

Interior:

Door trims $25 each

Inside door handles $15 each

Climate control unit $40

Steering Wheel (3-spoke) $15

Indicator Control switch module $25

Wiper & washer Control switch module $25

Side vents $5 each

Rear/back seat $40

Rear/back trim $25 each

Steering column surround $20

Under steering covers $15

Centre A/C vents + surrounds $20

Centre Console $20

Dash board (no cracks) $50

Dash instrument cluster 121000 (GTS) $40

P/window switch control (driver window button doesnt spring down, but operates fine) $10

P/morrors switch control $15

I have other parts that I havent mentioned, so if your in need of something thats not listed just ask and i might have it, thanks.

  • 2 weeks later...
  • 1 month later...

I apologise for not replying to all the message and any inconvenience i may have caused. i have been away for sometime

due to personnel matters. Most of the parts that are listed are still for sale. My number is 0416 066 540 if anyone wants to

contact me direct.

Regards

Sam.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
×
×
  • Create New...