Jump to content
SAU Community

Recommended Posts

I've got a black Series 2 R33 skyline up for wrecking... It's been hit in the right front qtr...so radiator, condensor, front bar, front right qtr panel, rad support are gone...but mostly everything else is up for grabs...

If your after anything just pm me cheers...

Engine Bay

Rb25det 116xxxkms with loom and ecu (remapped by dr drift) & Splitfire coil packs - $2400ono

post-36648-1233733820_thumb.jpg

S2 Rb25 turbo with actuator, good cond, minimal shaft play. Didn't blow any smoke - $250

S2 AFM (pink sticker)- $90

R33 aircon compressor pump - $100

R33 power steering pump - $100

R33 alternator - $80

Fuse box lid - $20

Stock airbox & snorkel + filter - $75

Exterior

Gold 18" x 8.5 (+15 offset) Gravity Gullframes with tyres (90% tread on 2 tyres), one wheel has gutter rash - $1200

Passenger Side Headlight - $150

Driver side Door - $180

Passenger Door - $180

Boot Lid - $200

Stock Rear Bar - $90

S2 Spoiler - $50

Nismo Side Indicators - $50

Interior

Instrument cluster, white face $150

Dash surround (with clock, hazard switch etc) - $80

Gear stick surround - $40

Ashtray - $20

Glovebox - $40

Steering column surround plastics - $25

S2 dash pad (no passenger airbag & panel) - $40

Centre console - $50

R34 Front seats - $150 (to fit r33)

R34 Rear seats - $100 (fits both r33 and r34)

R33 S2 Front seats (drivers side has a tear in the usual spot) - $80

R33 S2 Rear seats, good condition - $40

Seatbelts, full set - $80 (will seperate)

Ignition barrel + door barrels + key - $100

other parts...

Cat Back 2.5" to 4" tip - $150

Dump pipe - $50

2.5" Front Pipe - $100

Hybrid Front Mount Intercooler - $200

Pm me for any other parts cheers...

post-36648-1233734526_thumb.jpg

post-36648-1233735497_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/255566-wrecking-s2-r33-skyline-gtst/
Share on other sites

  • Replies 79
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...

Manual Conversion - SOLD

Side Skirts, Rear Bar and Duck Wing - SOLD

5 Stud Conversion - SOLD

Full Exhaust - SOLD

Also have....

Apexi RSM - $250

HKS EVC 5 - $380

R34 APEXI POWERFC - $900

New price for RB25DET - $2200 (includes SPLITFIRE COIL PACKS) i want it gone!!

18" BBS rims - $600

post-36648-1235122438_thumb.jpg

post-36648-1235122504_thumb.jpg

heres piks of my 18" gravity's - $1200 =)~

post-36648-1235122652_thumb.jpg

post-36648-1235122716_thumb.jpg

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Well, hydraulic lifters will get noisy if they are dirty/fouled in some way, and exactly how that manifests will depend on exactly what schmutz is where. There is a procedure on here somewhere for dismantling and soaking/cleaning them. Replacing them with new is about 50% of the work and about 5% of the money!
    • Thanks for the reply @GTSBoy this is is a hydraulic lifter engine. Yea right i did not realise the lifters were supposed to be compressible while installed. I could push them down but i had to lean almost my while body weight on them.  I have never heard of a lifter/ lifters ticking only at hot idle and getting worse the hotter it gets. I have owned a few jdm cars with noisy lifters. This noise is slightly more subtle, it is more of a sharp gentle metalic tic than the solid and more loud tapping I've heard on lifters. I have used a metal rod, alloy tube, hose and stethoscope and could not find the source of the tick. But it appears to be loudest on the actual engine block behind the exhaust cam gear and next to the oil filter. I had mate (40 year old mechanic) go over it with me and he couldn't find it either..  Could it be a cam seal issue of some sort?  Cheers  
    • This seems problematic and unlikely at the same time. Vanilla RB2Xs have hydraulic lifters. They do have "zero" clearance, but only when running with oil pressure inside them. When not running, you should be able to compress them and obtain heaps of clearance. RB26s and Neos have solid lifters. They should have ~0.3mm and ~0.5mm on the inlet and exhaust respectively. If they have zero clearance then bad things are happening. With nothing else being wrong, it would mean that the valves would be held slightly (ever so slightly) open when they are supposed to be closed and it should have all sorts of problems when running, caused by leakage in/out through the valves. Or, zero clearance can indicate severe valve seat recession. None of it is good. Have you used a piece of hose as a stethoscope to try to localise the noise?  
    • Sorry for reviving an old post, but I'm having the same hot idle tick issue. Did anyone ever find out what it was?  I have checked/ replaced Injectors Coils checked Lifter clerance (is at zero) Checked Cam lobes Replaced exhaust gasket and studs Would appreciate any advice this is driving me nuts  
    • There's a huge reason manufacturers are tuning in dead flat torque curves... Make them reliable (and more drive able)
×
×
  • Create New...