Jump to content
SAU Community

Recommended Posts

hey im having a cleanup and sellin all the stuff i dont need. if you interested send me a pm or give me a call 0406751986... some parts negoitiable.. everything is available to pic up or post at buyers expense

RB25 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange used 3000k's $100

RB30 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange.comes withs gaskets. new and never used $150

Coilpack wiring $20

Ignighter box $30

38mm wastegate $50

RB25 dump $20 3 avail

Exaust manifold $30 2 Avail

Ignition Barrel with genuine key $30

inter cooler piping for front mout stainless. $20

Injectors in rail.. only 5 injectors. cant find the other atm.. injectors require clean because they been sitting aeound a while. $50

Throttle body s1 and s2 $40 each

s2 tps $30

Coil packs s1 $70

intercooler pipe with adapter for blitz blowoff valve. it can replace the standard pipe in that position $30

Gredy boost Gauge $30

Genuine oil filter $10

tomie 1.2 oil restrictors x2 $15 each

Standard intake pipe with blow off valve... one with out $30 each

cam gear cover $10

Oil cooler adapter with fittings $40

300zx oilcooler $10

genuine injector to manifold seals $10

Genuine rb25 headgasket 87mm bore $50

RB25 requires rebuild. belt came of at idle and broke 2 valves in cylinder 1. had 130000 ks, run fine before that, will come with good cams as it has been sitting around for a while and the lobes are pitted. comes with oil pump and harmonic balancer, $200

flywheel will need machining $20

Genuine inlet manifold gasket where it splits $30

charcoal canister $20

Washer Bottle with motors $30

wiper motor $30

coilpack cover $20

Maroon r33 wing make an offer... also have rear bumper

r33 dash make an offer.. welcome to come inspect

silicon right angle 2.5 inch bend $20

right angle fitting in pic (not speed flow) $10

Heat shields for manifold and turbo make an offer

complete inlet manifold with injectors, sensors, idle controll valve ect.. $200

top half of manifold x2 good for changing to a forward facing plenum $40 each

bottom part of manifold $10 requires new coolant outlet

plenum chamber $20

ALternator.. has been tested $70

power steer pump $50

standard turbo to airfilter pipe with adapter and k & n airfilter requires clean $30

some standard intake pipes in the pictures if you interested let me know and make an offer

please check the link for pictures http://www.boostcruising.com/forums/index....howtopic=384000

Link to comment
https://www.sau.com.au/forums/topic/255741-r33-skyline-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I'm keeping an eye on it and might take it out as a once off if this doesn't fully charge. I did some research that said it's normal in equalisation charging. Voltage I thought was 20+ (faulty battery in multimeter) but now its on 15.9v, the max it should go to is 16.2v as per the manual. I'll provide an update once hopefully it's actually fully charged and in float mode. Waiting for it to go to 16.2v and not higher and see what happens. What I suspect has happened is that even though it's not an old battery, I did leave the car turned off for almost 4 weeks at one point then left it off for another 2 weeks which might have erroded the battery and is taking a long time to do this equlisation charge.
    • I wouldn't be using the seats a lot since it's on Historic rego and will not be driven a lot, however I also don't want to fork out 3k for something that won't last. Havent looked at BRZ seats, aiming for something of the same era I did speak to him on the phone once, and I do see your point haha. How many kms do you think you drove before they started wearing out? Just had a look at yours, certainly looking for a reclinable version. The Brides don't look too bad! I would still like to sit in one just to make sure it's what I'm after.    Thanks for the replies fellas. 
    • I bought my Bride reps from Crank Motorsport. He is, um, a trifle disorganised. I would have to look back at the e-mails to make sure I got it right, but I think he sent me normal fabric ones when I ordered the "Alcantara" ones. So he had to pay for shipping 3x and I'm sure that f**ked him off big time. And asking technical questions where nuanced English is required is a no go. It's simple English only. And....should I have bought the Alcantara ones? Well, as it turns out, they are great, feel great, etc, but the fabris wore through on the point of the waist bolster in <2 years. Must have caught a rip from a rivet on jeans or shorts, or something like that. So now I have to patch it somehow. A bit shit. My fault, ultimately, because it is Chinesium Faux Alcantara, not the real thing, and it turns ot that it has the tear resistance of a soggy tissue. But the seats and the reails are great. I probably should have gotten the R34 style ones, and now that they price is up in that ridiculous sort of number, I could have sold them for a profit!
    • Another recco is to just let it rest for a while and go back and reconnect later.
    • keep an extinguisher nearby? or even better, take it out of the car to charge?
×
×
  • Create New...