Jump to content
SAU Community

Recommended Posts

Hi guys,

I am intending to purchase 400R side skirts for my R33, but I noticed that there are some going around without the little vent thing in them, (i.e. without the cut outin the side skirt)

Are these also 400R side skirts, if so, where can I get my hands on some that don't have the cut out (saves me from having to fiberglass the one with the hole)?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/256843-400r-side-skirts-help-needed/
Share on other sites

Show some pics.. then we can look at what side skirts your talking about (might not even be 400r

If you go to the following link you will see them:

http://www.skylinesaustralia.com/forums/40...400R+sideskirts

As you can see the skirts on the white R33 don't have holes in them....

dont touch anything off ebay.

I would say that white 400r kit might have white mesh on there.

Having said that however i got some jun sides off ebay. They didnt have holes cut, the were broken and they were of real shit quality.

NEVER BUY A KIT FROM EBAY

^ worst advise ever

when u get it painted, ask the person to fill up the hole

Its not a big job but may cost a little extra

I will be painting and fitting them myself, it would just save me time not having to fibreglass it by getting it without the whole.

Thanks anyways lads.

the only reason I suggest mybodykits off ebay is because Ive bought quite a few things off him full kit m-sport r33/r32 gtr front bar/r33 trial front bar and they have been the best quality fibreglass I've used anyway its up to you..

the only reason I suggest mybodykits off ebay is because Ive bought quite a few things off him full kit m-sport r33/r32 gtr front bar/r33 trial front bar and they have been the best quality fibreglass I've used anyway its up to you..

Yes I did purchase them from him, good quality stuff I must say, feels very sturdy.

I fiberglassed the holes and painted them. Will post pics soon. job turned out well, would have saved me some time but not to fibre glass them.

the only reason I suggest mybodykits off ebay is because Ive bought quite a few things off him full kit m-sport r33/r32 gtr front bar/r33 trial front bar and they have been the best quality fibreglass I've used anyway its up to you..

:D

Should always pre fit body kits cause they rarely fit. You might get lucky but more then likely you may have to do some changes to get it to fit.

WHat sort of changes? WHy would painting it matter?

If you did have to make alterations, commen sense tells me that it would be on the edges or on the inside of the side skirt, why would you have to modify the outside of the skirt since it doesn't impeed on anything?

well if you had to modify the edges on top of the paint job it would be seen wouldnt it? In that case if you wanted it to look pro you would have to re do the paint.

Common sense would have told me to pre fit before paint but what ever you say.

well if you had to modify the edges on top of the paint job it would be seen wouldnt it? In that case if you wanted it to look pro you would have to re do the paint.

Common sense would have told me to pre fit before paint but what ever you say.

And you'd modify edges on the top that don't touch anything because....??

as i said because it would be SEEN! When you open the door. Also what if you havent sanded it down enough and you close the door and it hits the skirt, then you will chip or remove a layer of paint/fibreglass.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi all. So one of my major issues at the moment is my rear turbo leaking oil on the exhaust (and the general area). I presumed it was the rock hard super old drain hose, which it was not. So now I am in the midst of removing the rear turbo to get access to the banjo bolt that goes into the turbo oil feed. As one of the previous owners accidentally? tore off the OEM oil feed hardline that reaches behind the turbo, they ran braided lines directly to the turbo, presumably PTFE. Now, regardless if the line has rubber or teflon inside, is it just generally a bad idea to do this? I imagine these lines get quite hot being between the engine, turbo core and exhaust manifold. I suppose it's not too far fetched to think the line may even have melted. I'd love to hear your opinions on this as as the replacement OEM hardline piece is 130 per unit. And cutting open the currently mounted line to see inside will mean I just have to get a replacement either way. So far I am hoping maybe the bolt just loosened or (god forbid) they forgot one of the crush washers.
    • If it's a factory 20de manual probably has the 6 bolt flywheel in which case the det clutches won't work as they're 9 bolt.
    • All RB push clutches are interchangeable. AFAIK, the 4cyl ones are not. Different flywheels. The RB small box is not identical to the 4cyl boxes. Just very similar.
    • Hi. I need a new clutch for my gearbox. It is a factory smallbox behind RB20DE NEO. What options do i have? If iam not mistaken the gearbox should be the same as in R32 GTST and Nissan S14/S15? I found some Xtreme Clutch Stage 1 for S14/S14 (i dont know if you know the brand) (UK) OR...is the clutch same as in the bigbox from RB25DET?   Thank you!  
    • Listening to an artist called "the flashbulb". Not bad. Makes some fairly well researched youtube vids in various things.
×
×
  • Create New...