Jump to content
SAU Community

Recommended Posts

Okay, I love bass. I never truly realized how much I did love it till I bought my Alpine Type R 12" sub. What I enjoy most is more the physical sensation of a powerful bass pushing my innards around, more than high dB or neighborhood waking "doof doof", but I suppose they all go hand in hand.

So I sold my last car, sound system and all, and I'm looking at making a really nice set up in my next car, but I don't really understand all the technical jargon.

I'm trying to find what I was looking at earlier, and can't find it anywhere now. Subwoofer's come with their own SLP(?), SLQ(?) ratings, something like that, and I have no idea what each means.

Anyway, if I come across them I'll post them here again.

In short though, for the best physical sensation from a sub I'm guessing you want a larger surface area more than anything? Like, two 15" subs will out perform a single 12" even if the 12" has a slightly higher RMS value than the two bigger combined?

Thanks guys.

Link to comment
https://www.sau.com.au/forums/topic/257500-subwoofer-basics/
Share on other sites

Normally subs will not come with a rating for what there better for however they are generally supplied with T/S paramaters (Theile / Small). From these specs you can normally work out what the sub is better suited too.

In the big scheme of things the RMS value of any speaker means very little and it is not something to use to compare different models with, the RMS value is just a thermal rating meaning sure the voice coil may be able to handle that amount of power but you would have far surpased the mechanical limits of the spider and surround before you get anywhere near that value.

The larger the surface area of the woofer(s) that you are using the better. Obveiously the bigger the moving surface / mass the louder and deeper it can play with less stress placed upon it.

There are alot of other factors to consider when looking at subs such as the Xmax, Fs, values.

Remember tho a sub is nothing without its enclosure,even a single 12" in a properly designed enclosure is enough to give your internals a good beating.

What subs are you currently looking at?

Jack

Edited by Jack88
Normally subs will not come with a rating for what there better for however they are generally supplied with T/S paramaters (Theile / Small). From these specs you can normally work out what the sub is better suited too.

In the big scheme of things the RMS value of any speaker means very little and it is not something to use to compare different models with, the RMS value is just a thermal rating meaning sure the voice coil may be able to handle that amount of power but you would have far surpased the mechanical limits of the spider and surround before you get anywhere near that value.

The larger the surface area of the woofer(s) that you are using the better. Obveiously the bigger the moving surface / mass the louder and deeper it can play with less stress placed upon it.

There are alot of other factors to consider when looking at subs such as the Xmax, Fs, values.

Remember tho a sub is nothing without its enclosure,even a single 12" in a properly designed enclosure is enough to give your internals a good beating.

What subs are you currently looking at?

Jack

Well, besides a bit of online research I only know what was around 8 months ago. Like I said I had a 12" Alpine type R (in an Alpine ported box designed for it), I loved it, but next time I want more.

I know nothing about 15" or 18", but I was considering a pair of 12's. From memory Fosgate, Kicker and Alpine Type X are the next level up. Like I said though, volume isn't such a big deal. Ideally I want very high quality sound, and a nice strong physical punch that you can really feel. I'm guessing that means a pair of quality 12's or a nice 15"? Both in sealed enclosures?

Saw this today;

http://cgi.ebay.com.au/soundstream-xxx-15-...%3A1|240%3A1318

Overkill? I know nothing about the brand, but it seems pretty cheap, so long as you can afford the amp and batteries to support it.

Thanks for the response.

Edit: Quick question; what size sub(s) can you fit in an R34 boot?

Edited by KezR33

soundstream 12s are apparently enough to make a R33 rattle, so i would say, yes that would be over kill for what you are looking for.

Kicker make some decent subs, i would probably look more towards the Alpine though. two 12s would be more then enough bass, if you power them correctly, OHM, WRMS, etc etc

Best bet, go to a audio specialist, listen and chat to them about it. They will help you out a fair bit.

Cheers,

FYI, two 12" will fit hidden behind the panels in a R34 GTT. in fiberglass boxes. I have 1 there now but room on both sides

two 15" will fit if you dont want a boot anymore same for 18, plus the car will self destruct from vibrations,, along with the all the birds in the trees and kids on bikes .lol

a well designed system is better then just generic parts tossed in and hope it sounds good. a single 10 can rip your head off if done right? ???

Im not a huge fan of 12's but for some reason oz had that as a standard rather then 10 or 15 ? along with the dreaded 6x9's.

yes I know jack88 my car has a 12 but only because its a left over from my old car....so dont start..lol

in the next incarnation its going to be a 10 or 2 digital design 8 inchers in a single reflex carbon fiber box. ported thru the rear deck

the higher the sensitivity in DB to start with the less power it will take to get loud, every 3 db is around 2 to 3 times the power level to increase the sound output

so a 89db woofer will need more power then a 91db woofer to reach 120db. but there is a lot of other things to consider. the box design, a sealed box isnt as the best but will control a woofer up to its tuned freq before distoration. and sounds smoother most of the time. at a lower cost to construct then a bandpass box.

so many varables to deal with for a pro system

rather then writing all this out for you, have a read here?

http://www.the12volt.com/caraudio/boxes.asp

if you need help just pm me. figure out your budget and if your a brand loyalist we can go from there ?

cheers

Troy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah right. Maybe my rb just loves chewing through batteries lol.
    • On the R34 can't you just unplug the IACV? This is the way I've always done it on the R33. Disconnect IACV, get it idling around 650rpm, and then do a power reset on the ECU to get it to relearn idle (factory ECU).   The big reason no one has touched on as to why you'd want to get the base idle right, is that it means the computer needs to make smaller adjustments to get a good idle at 700-750rpm.   Also, cleaning the IACV won't normally make the car suddenly idle lower or higher. The main issue with the IACV gumming up is that the valve sticks. This means the inputs the ECU gives, aren't translating to changes in air flow. This can cause idle choppy ness as the ECU is now needing to give a lot of input to get movement, but then it moves too far, and then has to do the same in reverse, and it can mean the ECU can't catch stalls quickly either.
    • 12.8 for a great condition, fully charged battery. If the battery will only ever properly charge to about 12.2V, the battery is well worn, and will be dead soon. When I say properly charge, I mean disconnect it from the car, charge it to its max, and then put your multimeter on it, and see what it reads about an hour later. Dieing batteries will hold a higher "surface charge", but the minutest load, even from just a multimeter (which in the scheme of things is considered totally irrelevant, especially at this level) will be enough over an hour to make the surface charge disappear.   I spend wayyy too much time analysing battery voltages for customers when they whinge that our equipment (telematics device) is causing their battery to drain all the time. Nearly every case I can call it within about 2 months of when the battery will be completely dead. Our bigger customers don't even debate it with me any more ha ha ha. A battery at 12.4 to 12.6 I'd still be happy enough with. However, there's a lot of things that can cause a parasitic draw in a car, first of which is alarms and immobilisers. To start checking, put your multimeter into amps, (and then connect it properly) and measure your power draw with everything off. Typical car battery is about 40aH. Realistically, you'll get about half this before the car won't start. So a 100mA power drain will see you pretty much near unstartable in 8 days.
    • Car should sit at 12.2 or more, maybe 12.6 or 12.7 when fully charged and happy. If there is a decent enough parasitic load then it will certainly go lower than 12.2 with time. You can't beat physics.
    • Ok guess I can rule out the battery, probably even the starter and alternator (maybe) as well. I'm gonna clean those leads and see what happens if it's still shit I might take it to an auto electrician. Unless the immobiliser is that f**king heavy, but it shouldn't be.  If I start the car every day, starts up perfectly never an issue. Isn't 12v low, shouldn't it be around 12.5v?
×
×
  • Create New...