Jump to content
SAU Community

r30 skylines


rsx84
 Share

Recommended Posts

  • Replies 2k
  • Created
  • Last Reply

Top Posters In This Topic

konis/kings, seems to be all right but will see as time goes by how firm the konis stay, a mate has them on his r30 put them in about 9 months ago and hes saying there are getting soft, his is a daily driver, mines gone 60km since the ignition was wired up, i can say cornering is flat and fast!!

Link to comment
Share on other sites

anyone seen the second last page of the latest HPI mag as there is the whole page to the DR30, small write up not to much info what they do say though is stay away from a dr30 for under 10,000 and be prepaired to pay up to 15,000. Also i emailed the bloke about the RS turbo booklet and he said its in japanese, but he did say that hes got a 20 foot container of dr30 parts and panels plus a couple of cars comming over in march so if there are things people are looking for then he may be to go!!

Link to comment
Share on other sites

ah yes that SA GUY....sed he had a dr30 diff he would sell me for $1300....wtf.

on the dr30 front bar issue, got a qoute for one ..800$ landed from that jenesis place

1300 on a r200 diff i quess??, the front bar quote is that through rezz or jenesis itself?

Link to comment
Share on other sites

I haven't actually pulled the diff apart to look yet. It open wheels and twins up then opens again so it ain't in the greatest condition. Probably just shimming or drive plates just guessing. I wanna change ratio's as well but that could be expensive.

sounds very much like my diff, under load it twins, but free spin it has one going one way and the other spins the other way?? was told the diff in a pintara has the perfect ratio for track and was a good swap?? thats what i was told!!

boof- pm'ed stu-r30 with the details and seems hes done deals with him?? may be ask stu-r30 what he thinks??

Link to comment
Share on other sites

Yeah pintara's run 4:11 ratio which would be more what I want. How ever they run borge warner solid axle diff's a little different.

Anyone know what diff ratio DR's run standard exactly? seems pretty high as the gearing is quite long, 115kmh in 2nd pushing it.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...