Jump to content
SAU Community

Recommended Posts

@@@@@ GUARD FLARES @@@@@

Hey Guys,

Go to www.r31skylineclub.com, then open link to Forums, then scroll down to trading post, "Parts" and fatz (Pete) has a group buy for $300.00 set delivered.

$50.00 deposit gets it all up and running.

Cheers.

  • Replies 2k
  • Created
  • Last Reply

Top Posters In This Topic

finally got my car sorted - took it for a spin and...hello boost

noticed a few things - brakes need serious attention, tailshaft hits somewhere and also i cant get the grin off my face hehehe

i found that the changes i made to the brakes are great (for now) r32 master cylinder, slotted rotors and good pads, but if you do some minor changes you'll notice a change! pads, fluid, machine the rotors things along those lines, in the wet the other day pulled the car up from 140km to 40km in around 60m, dont think i've had a car with that kind of stopping control, i do have brand new tryes on though!

mate it goes a bit better than the L20et dosent it, i run mine around the block a few times with no intercooler and then once the cooler was hooked up took her to work with me :aroused: mate the boost on mine kicks the rears around a bit, worth all the money i've spent so far the first time i dropped the clutch :headspin:

ANYONE NEED ANY BITS FOR THERE CARS AS I'M TAKING MY MR30 HATCH TO MY MACHANIC ON TUE TO TAKE THE REAR CALLIPARS OFF AND THEN TAKE IT TO THE WRECKERS SO IF YOU NEED STUFF PM ME AS IT'LL BE AT POSTAGE COST TO YOU?? cheers.. Matt

']arent those flares for 31's though? hmm id be interested but i just dont have big enough dish & spacers to make use of em! would make my wheels look tiny! lol

They are! BUT!!!! if you go to the Jenesis site, www.r30.co.jp and open the BODY link, you will find "Fender Trims" and the picture of the carbon bonnet shows them, they look identical to these R31 flares.

I don't know if we need them unless using huge wheels, like 9 inch + wide.

I am not going to fit them until after the adjustable rear goes in, to see if & when the rear wheels are at zero camber and toe, how they sit in relation to the body, and I have 16 x 8's all round.

Cheers. :ghost:

They are! BUT!!!! if you go to the Jenesis site, www.r30.co.jp and open the BODY link, you will find "Fender Trims" and the picture of the carbon bonnet shows them, they look identical to these R31 flares.

I don't know if we need them unless using huge wheels, like 9 inch + wide.

I am not going to fit them until after the adjustable rear goes in, to see if & when the rear wheels are at zero camber and toe, how they sit in relation to the body, and I have 16 x 8's all round.

Cheers. :ghost:

i'd say they would be good if we were looking at the gtr brake upgrade as i have 7" and 7.5" wide rims and they fit perfectly if i run the gtr front brake set up and these rims i'd have 1/2" gap!

RE: Flares

You'd have to have some pretty wicked offset wheels to make use of them I think.I have 9inch rears,on an HR31,and I know they're different,but they it good.Also a mate's old DR30 had 9" rears,and fitted snug also.They were Sparco Python2's though,so not that deep a dish.....

Also,I think the local boys are getting them done from fibreglass?

RE: Flares

You'd have to have some pretty wicked offset wheels to make use of them I think.I have 9inch rears,on an HR31,and I know they're different,but they it good.Also a mate's old DR30 had 9" rears,and fitted snug also.They were Sparco Python2's though,so not that deep a dish.....

Also,I think the local boys are getting them done from fibreglass?

If you went back a few pages to the link rsx84 posted about the Japan R30 Meeting, it was then discussed on wether these flares were available here???

I simply say, they are and from where. R31 Skyline Club are getting them made locally (Sydney).

I don't think they are necessary either, but I won't know for sure untill I get my camber on the rear wheels sorted out. Once I get the rear wheels to zero or -1 max, I won't know if they are needed.

I have 16 x 8's on now and they sit fine, neatly inside the body without rolling the guard lip, and the wheels are +38 offset, (std is +25) and I still clear the coilovers on the inside.

I don't know if I can get 9's on, but I will see later down the track.

I have 16 x 8's on now and they sit fine, neatly inside the body without rolling the guard lip, and the wheels are +38 offset, (std is +25) and I still clear the coilovers on the inside.

hmm interesting.. i had 17x7 +38 offset wheels on mine and they sat in the guards terrible, had about 7-10mm clearance between the strut and tyre.

and they also rubbed on radius rods on full lock

s13 coilovers almost bolt in, the front strut tops are the same patten, for the rears i swapped strut tops. They work a treat for me and so do the big brakes, i bought a set of JIC coilovers for $500 :)

On the topic of custom parts, Ghostrider is right, its cheaper to have them made, at the moment i have a half cage, castor rods, adjustable front control arms, rear strut brace, rose jointed swaybar links, rear floor brace, custom oil catch can, custom inlet plenum and a few other items being made up here in adelaide for a reasonable price.

You can slot one of the swingarm mounts safely to correct camber problem in the r30s, works a treat, but be cafefull who does it, best left to an engineer.

Picked up an LSD on the weekend at a cheap price, but its a 3.9 ratio, i was looking for a 4.4, does anyone have an R200 open wheeler, or crownwheel and pinion in a 4.4 or 4.6? I plan on swaping the LSD into a housing with 4.4 or 4.6 ratios.

Also picked up a very thick K-mac front swaybar.

Im interested in a t-shirt too :D

OK just a quick question when i got my dr30 "iron mask" months and months ago the iron mask was coming off at the RHF section. The question being how do i fix this? is as simple as a industrial staple or some sort of clamp? the thing is it was attached by the japs with what looks like masking tape, interesting? Another quicky can we install a australian standard battery, is there enough room? actually theres another one do i have to buy the window seals or can i get them made up by someone?

I know these are dumb questions, but still....

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, the other thing I've sorted is a baseline dyno run up at Unigroup's new location. The auto trans was a little unco-operative by both shifting down when the throttle was floored on the dyno (so Mark had to ramp it up more slowly than in a manual) and also by shifting up at 6,000 even in sports mode instead of the indicated redline of 7,000 Still, on a hot day it made 240rwkw at 16psi which seems about right for 300kw (400hp) through an auto at the wheels.  The shape of the curve is not quite right because it was not full throttle to about 4,500 to stop it kicking down, but until I can get a tune on the auto trans control this was the best we could do.....full boost will be well below 5,000 once that is sorted, I'll get some data logs when I can to confirm For comparison, the R32 made 255 at 12psi (at 4,500) on the same dyno with tune, n1 turbos, cam gears, big exhaust but otherwise all standard so the v37 is likely a little better out of the box. One thing that is very clear is that the standard water to air intercoolers are not up to sustained use at full throttle in warm ambient temps. After about 5 runs (so only a few minutes full throttle), it was pulling boost and timing and dropping 10-15% power. Unfortunately I didn't get that printout and the Unigroup guys are away at the moment, will try and get hold of it on their return. So, looks like a healthy engine to start modifying and the only real area of concern is the w2a heat exchangers which the aftermarket has plenty of solutions for    
    • I maintain it actually looked really nice in person. So much so that I thought "No, this is illegal" but there it was, clear as day. I think we can easily call the wing and wheels/height to be transformative. Not saying it's better than the GR Whatever, or the 86, or the WRX STI or anything of that sort (the internet says it all bolts up so you can buy best of all worlds?) but it's still at least a thing and not nearly AS bad as people say.
    • That's less offensive than the previous gen.....except for all that ugly black tupperware around the edges. Blerck!
    • I leant out the window recently and took a picture of this new WRX. It looked real damn fine in person. It's faster around a track (stock) than a (stock) GR Yaris. It's much more practical despite being heavier. It's significantly cheaper. This gen tunes really well, much better than others. .... I think they're probably a lot better than people expect.
    • WRXs are a pure pleb boring car these days. You need to get an STI to even get close to what a WRX used to be.
×
×
  • Create New...