Jump to content
SAU Community

Recommended Posts

boost is not related to stock coils keeping up or not

they simply die of old age

so you can run 27psi if you like

one day they will die and misfire regardless of engine boost

once the engine is on load, it will misfire

so run whatever you like

1.3kgcm2 if you want

the turbo is a high flow, the ecu is std but has a haltch intercepter connected which has been tuned, The engine has forged pistons. Im guessing the coils are as old as the car. Someone told me it could be the higher boost is blowing out the spark?

breaking down spark is different to coils dying

coils die due to age, when they die, like i said, they misfire as soon as the engine is on load

ie one day its fine, next misfire city, so its all of a sudden.

spark breaking down is usually too much boost or wrong gap or intake temp too high

or combination of all three usually. if running less boost cures the misfire its probably spark breaking down

my coils lasted 160,000 then gave up

coils die due to age, when they die, like i said, they misfire as soon as the engine is on load

ie one day its fine, next misfire city, so its all of a sudden.

In my experience the typical coil misfire is the insulation giving out, everyone I know who has put work into decently re-insulating them have fixed it fine. I run up to 18psi on my original S2 R33 coils with extra insulation on them is going fine :(

Yea it happened really bad one night when the air was still pretty hot. I found a few FAQ's on how to insulate the coils, So i might give that a go and replace the spark plugs. What better out of BCPR6E or BCPR7E? Or do people recommend any other ones?

who can repair coils?

I have splitfires in mine atm, sometimes when I leave car to warm up in morning, it will run on 5 cylinders, ill go out, disconnect connection to coil #3, plug it back in and away it goes back on 6 cylinders.

But when I drive and give it a little stick, it starts miss-firing so i assume its that faulty coil?

who can repair coils?

I have splitfires in mine atm, sometimes when I leave car to warm up in morning, it will run on 5 cylinders, ill go out, disconnect connection to coil #3, plug it back in and away it goes back on 6 cylinders.

But when I drive and give it a little stick, it starts miss-firing so i assume its that faulty coil?

the 10+ year old plug or wiring is likely at fault vs a new ~ish splitfire coilpack set

You can also get the coil pack loom from Nissan for around $140AUD from memory... its pretty cheap if the plugs are a bit stuffed.

I purchased new for mine with the splitfires, good insurance.

And for the record i made 370rwkw on stock RB25 coils, they were in very good condition :D

You can also get the coil pack loom from Nissan for around $140AUD from memory... its pretty cheap if the plugs are a bit stuffed.

I purchased new for mine with the splitfires, good insurance.

And for the record i made 370rwkw on stock RB25 coils, they were in very good condition :D

yeah...quite a high price..it might be better to find a private seller they might charge 30 bucks or lower.

A private seller for a coil harness?

I paid $120 for mine from RHDJapan, with shipping it worked out to the same as getting it from Nissan but got it in one week instead of three. I looked up the harness on RHDJapan recently and they're up around AU$270 delivered now :)

I was troubleshooting a misfire when hot issue for AGES, turned out it was the insides of the coil harness plugs falling apart.

yeah...quite a high price..it might be better to find a private seller they might charge 30 bucks or lower.

I meant quite low price considering…

Why get one 2nd hand for $30 only to have the same damn problem 6 months later?

Makes zero logical sense. You cant get them much cheaper as bubba has pointed out :)

Pay the Nissan price, its actually reasonable in price for something OEM and after 10-15 years does need replacing

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...