Jump to content
SAU Community

Recommended Posts

Had the 100k service done at Boostworx yesterday, belts, water pump, all fluids, diff, gearbox, attessa, brakes etc. I did my own oil and oil filter so that wasn't needed. They also fixed my dodgy front/dump pipe install and reseated the O2 sensor properly (didn't quite go all the way in before due to wrong thread on JJR's pipe). Car is now running like new, purring along beautifully, gear changes are much quicker and smoother. Couldn't be happier. If anyone has been putting it off, do it, do it now, worth every cent! They also put it on the dyno, 135rwkw. Total cost incld. 3 new bulbs, $1050.

Just thought I would share. :D

EDIT: Forgot to add that they changed the plugs too (supplied by me)

Edited by webng
Link to comment
https://www.sau.com.au/forums/topic/257716-just-done-100k-service/
Share on other sites

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

I'm a huge fan of Shaun, Troy and the guys at Boostworx.

Took my GTR there for it's first service + 100k stuff. Had it dyno'd and everything. Got it back and it ran alot better!!

Just recently got a brake upgrade done by them, too.

And will soon be back for more work!

+11789239923645928598256 Boostworx

Yep mines a RS4 (AWD) but their dyno is only 2wd so they dropped the shaft. Shaun mentioned 135rwkw is normal for the minor mods mine had, with all running well. Shaun and Troy have a couple of new guys there too, another mechanic (Andrew?) and an aprentice mech (Alex?). Both good blokes.

They're still pretty busy but at least it's not that long a wait to book it in now! What I like about them is I don't have to worry about them ripping me off, they'll only do the work required and charge accordingly. A bit of a hike from where I am (Payneham) but well worth the trek. I only wish they have eftpos! Cash only hurts the bank like crazy. :D

my stags going in on the 3rd for its 100k... lookn forwood to seeing what it pulls..

there doing my 100k, ebc and safc install and tune for 1800.

im guessing its a little diff for the 26... im thinking i might try and get my hands on all the stuff and just get them to do the labour part.

my gf's brothers 180sx is their waiting to have the rb20 wired up, auto elec quoted 3k, boostworks quoted 500!

Mines off getting serviced at Road & Track... theyre close to my place (Enfield)

Getting all fluids dumped, flushed and replaced

Getting all filters replaced/cleaned

Getting new sparkplugs, injector seals and injector clean

Getting diff seal tightened, brakes checked, dyno run

Dunno if there was anything else that needs doing (they'll call me) but I can't wait... come on 5pm

-D

What are they charging?

Mines off getting serviced at Road & Track... theyre close to my place (Enfield)

Getting all fluids dumped, flushed and replaced

Getting all filters replaced/cleaned

Getting new sparkplugs, injector seals and injector clean

Getting diff seal tightened, brakes checked, dyno run

Dunno if there was anything else that needs doing (they'll call me) but I can't wait... come on 5pm

-D

I won't know until i get the car back, but around the $600 mark.

Got car back. Loads of stuff done today....

New Globe, oil and fuel filters, air filter cleaned, NGK platinum plugs fitted, new diff oil, new brake fluid, new steering fluid, new hicas fluid, new engine oil. 3 leaking injector seals replaced, injectors sonicly cleaned, tyres rotated, rocker cover retensioned

came out to just over $700 :)

BUT

I have to now

replace front rotors, replace front brakes, replace LH Rear crossmember bush, remove radiator and get it completely flushed out, leaking injector replaced, and 2nd hand r33 gtr gearbox fitted. Probably gonna cost me over $1500 including parts but I don't skip so I'm gonna grab new RDA slotted front rotor and get some bendix ultimates to replace my current ones cause I'm pretty happy with them....

then (if I get my contract renewed) get some 2860-7's, nismo FPR, tomei poncam-b, hks cam gears and a radiator shroud purchased and fitted at the same time I get my n1 water pump installed :)

Fun. but not for my wallet.

-D

Yep mines a RS4 (AWD) but their dyno is only 2wd so they dropped the shaft. Shaun mentioned 135rwkw is normal for the minor mods mine had, with all running well. Shaun and Troy have a couple of new guys there too, another mechanic (Andrew?) and an aprentice mech (Alex?). Both good blokes.

They're still pretty busy but at least it's not that long a wait to book it in now! What I like about them is I don't have to worry about them ripping me off, they'll only do the work required and charge accordingly. A bit of a hike from where I am (Payneham) but well worth the trek. I only wish they have eftpos! Cash only hurts the bank like crazy. :)

yeah im a fan i was sure you had dyslexia with your power figure and meant 153 not to worry

i come from st agnes to go there so almost half the distance again of how much your travel

the young fella isn't Alex but cant remember his name atm

Got car back. Loads of stuff done today....

New Globe, oil and fuel filters, air filter cleaned, NGK platinum plugs fitted, new diff oil, new brake fluid, new steering fluid, new hicas fluid, new engine oil. 3 leaking injector seals replaced, injectors sonicly cleaned, tyres rotated, rocker cover retensioned

came out to just over $700 :)

BUT

I have to now

replace front rotors, replace front brakes, replace LH Rear crossmember bush, remove radiator and get it completely flushed out, leaking injector replaced, and 2nd hand r33 gtr gearbox fitted. Probably gonna cost me over $1500 including parts but I don't skip so I'm gonna grab new RDA slotted front rotor and get some bendix ultimates to replace my current ones cause I'm pretty happy with them....

then (if I get my contract renewed) get some 2860-7's, nismo FPR, tomei poncam-b, hks cam gears and a radiator shroud purchased and fitted at the same time I get my n1 water pump installed :D

Fun. but not for my wallet.

-D

If there is any advice i can give ya mate

dont get the bendix pads....save some money and get lucas pads

bendix put out shitload of brake dust compared to the lucas

and lucas brakes better and can operate at a higher temperature

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Can't say I've had a bad experience with one on my car, then again it only gets washed once or twice a year... The wheels on the other hand, get a good spray often due to my shitty dusty pads.
    • @MBS206 thats pretty neat and tidy to me!  I'll get a photo of mine when I'm out there next. It might require multiple photos to understand the scale of the atrocities though... In total I have 4 sheds of varying sizes and layouts. Main shed is 14x8, second shed is 3x8, third shed is 11x2.5, fourth shed is around 6x4.  All are pretty much full.   The main goal of my cleaning tsunami is to make the main shed predominantly car and motorbikes only. Second shed is my metal fab room (2 x bench grinders, drill press, bench belt sander, metal band saw, scrap metal storage and some of my garden tools.  3rd shed is more bigger garden stuff, storage for engine crane, jack stands, concrete grinder, concrete mixer, air compressor lives there, and it now has two 2mx2m pallet racking shelves with itemised boxes holding building stuff, electrical stuff, plumbing stuff, etc, etc.  The 4th shed is Ryobi electric ride on mower, mini boom sprayer, ancient Kubota tractor, more garden stuff!  I have got a lot of shit....  Then there's the pool house (8mx4m) and the pool pump shed (4mx4m).  I built all of the sheds over the 11 years we've been here.  The main shed was a Ranbuild kit, the rest are all custom made to fit the areas available. Building the main shed taught me a LOT as I had no idea about building anything prior to that!  I've still got one more in me. It will be my man cave which I poured the extra concrete for way back when I poured the concrete for the main shed. The idea is the Skyline will be a centre piece of the main cave once (if...) it's finished.  I told my now 14 year old son yesterday that I will 100% drive him to his year 10 formal in 2 years. Still a long way off but at least I now have a date to work towards! 🤣
    • Modern oils are amazing. Add tyres to that as well.
    • Probably a smart choice to buy one vs build, purely for the motivation part as you said! Imagine the metal dust everywhere from grinding all the steel to build one. Ha ha ha!   Also, post a photo of your garage.   Mine is below, this is where I've been cleaning and have already half filled a caged 6*4 trailer. And this is after my cleaning expedition mentioned previously... The middle normally has a car in it, but I'm dumping things in the middle as I sort through them. And poor skyline was dusty and has had the lightest few drops of rain and now it looks atrocious and needs to be dragged back out and washed thoroughly! And yes to the right is technically another bay, you really can only see 2 bays out of 3 in this picture.  
    • It's more like on average the things I see a lot of things going wrong. Yes, usually the people who reach out are the ones who are having problems but on average it feels like mechanics and tuners here aren't really competent. I swing between thinking my standards are just way too high and wondering whether people really are just this dumb. I just had the strangest 10+ reply argument on a Facebook group over someone insisting that the factory R34 GTT boost control solenoid reduces boost pressure to 5 psi when it's on and raises boost pressure to 7 psi when it's off despite showing the exact plumbing in the factory service manual and the solenoid behavior detailed in the FSM.
×
×
  • Create New...