Jump to content
SAU Community

Recommended Posts

Hi guys, I posted this in another thread but it's a little obscure if anyone was wanting to find a how-to. I searched and found zip so thought I'd snap some pics of mine I did todday.

** I used two different size hole saws to cut the radii and simply used a cutting wheel to remove the rest. Lots of masking tape around the area to stop any damage from swarf.

Initially I mounted the pins, raised them a little to make contact with the bonnet and make a mark from inside. I then drilled a small pilot hole, and then masked on the template provided and went from there.

Measure six times, cut once I suggest! :thumbsup:

Made U shaped brackets to utilise an existing hole in the radiator support. The return down the front too to give some extra strength. Made these from 3mm steel. You can see I had to gring the bolt down a little to allow clearence.

22022001.jpg

22022003.jpg

This is the drivers side from under, nothing tricky really.

22022009-1.jpg

The passengers side was a little harder. I did this second to get the feel for it. This is a GTR bonnet so I hade to carefully remove some of the reo.

22022002.jpg

And the finished product! A bit of fine tuning is needed to get them just right, and it's very strong, not going anywhere. As a bonus the rubber stoppers they supply were the perfect length to allow a little preload so no rattles.

22022004.jpg

22022005.jpg

And a reminder that angle grinders with cutting wheels can bite.

22022006.jpg

Link to comment
https://www.sau.com.au/forums/topic/258154-aerocatch-bonnet-pins-into-an-r32/
Share on other sites

What a great read!! Came up really well...

I did the same thing 3 months ago, although mine is a fibreglass/carbon bonnet, so would have been easier to cut.

They work so well and look much cleaner than the old bonnet pin style..

Here's my finished result...

gallery_1569_106_158120.jpg

Was going to get my panel beater to paint them silver but he advised not to, paint might not stick properly and would most likely peel off from constant use...

Either way they're not as noticeable as the old bonnet pins, especially since it gets driven on the street...

i put these on my 32. the bonnet i used had all the supports cut out so i didn't have to make it fit around them.

the car also had had bonnet pins so i used the holes in the radiator support panel to fit mine but as you may have found it a bit to shallow under the bonnet to fit them so my bonnet which isn't real straight anyway doesn't quit fit flush. if i get a new bonnet i will install them the way you have.

oh and word of warning after a bit of work the lock in pins start to over balance and you need a tool to get them to lock down. i am not the only one to have run into this.

i got mine after seeing all the cars in targa tas last year with them and funnily enough your going in targa tas with some.

so these are regarded as street legal? Where did you get them?

yeah as they are flush fit on the surface of the bodywork most states accept these as road legal.

bensonmotorsports.com was the source for the woo... always in stock!

Nice one.

I have finally taken delivery of my carbon bonnet and a set of these bonnet pins.

I'm going to get Micolor to do it though as I would just mung it up if I attempted it.

Kudos to you for taking the time to do it yourself.

Regards

Andrew

Looks good, one of the more subtle ones which seems to suit the R32 better. How strong are the carbon bonnets with using Aerocatches. Is the carbon too rigid and brittle ?

No idea, it's got all the factory latches as well so it should hang together. the pins are only insurance.

great write up mate!

love these pins! so much tidier than the metal ones...

angle grinder = OUCH! hope your hand heals quickly...

I bought a set for my s13 a while back, but another "wooss" here

I took the easy way out (had my panel beater fit them while my car was in paint)

even he was nervous and he couldn't promise me a 100% guarantee on perfectly straight and flush fitment, but he nailed it first shot...

at first i was concerned they might bind up or become brittle, after sun/water/soap/dirt/dust etc but they are well made and with a tiny spray of wd40 stay nice and operable.

the only thing i could put them down for, is the pins themselves, they could be swapped out for some actual steel ones...

some pics from when i had mine done:

2008-03-12015.jpg

2008-03-28041.jpg

pins2.jpg

I tried to use some about 3 years ago but woosed out because i didnt want to cut up my GTR bonnet...maybe its time to second guess that decision :thumbsup:

lol, just bite the bullet Roy and do it mate, they look great and operate smoothly. I reckon they're the best part of the car now :D

Oh, guess what, the wheel Just turned up :D

If anyone needs it, i just made up a cutting/drilling template for the 125 Series, the one they supply is for the 120 series and slightly different.

Print it out full size and you should be sweet :(

Aerocatch_template.PDF

Ok, then where is the quickest and easiest pace to get them. Better shoot them off to the panel beater before the bonnet gets sprayed. Stuart?

They may look ok on my car since i am doing the fan boy black and silver thing :thumbsup:

Troy, got mine through revolution racegear, about $120 from memory....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I used the radium thing, makes the whole parallel assembly a lot more compact compared to any other way of doing it 
    • Racetronix also sells those ethanol content sensor bypass blocks. Adapter, Flex-Fuel E85 Sensor High-Flow Bypass, In-line No Sensor (ADF-FLEX-NS): Adapters - Flex Fuel | Racetronix Ethanol content sensor are originally designed to be on the feed line. These bypass blocks are meant to be ran in the feed line and not return. The continental ethanol content sensors have a 3/8" ID and not 5/16". This is why they are ran on the return line directly in conjunction with a low threshold sampling value VS in the feed with one of these blocks.    Haha we think alike, I used both original feed/return for 8AN feed, and one of the Hicas lines as a 6AN return. I also capped off and left the other Hicas line as a spare. 
    • Interesting, I haven't read about the issue with oil getting into the speedo in the cluster before. I'll have to take more notice with mine. The speedo on my R32's when I've run factory diff and tyre size have never been accurate as far as I can remember. The non Type-M GTS-t did come with 15" 5 stud wheels and smaller brakes, but that's less than 5% of them.
    • Good to hear the condenser you picked up off my brother worked all good. Do you think there could be an issue with your AC compressor itself or the clutch on it then? I don't know a lot about them so I can't really help but keen to hear what it ends up being. Keep the build thread going man, it's nice to look back on over time.
    • This is a story of my life things, I learned eventually (thanks to someone calling me out) that my enthusiasm for discussing and sharing ideas that it came across as arrogance and I'm like... WTF?!    One thing I'm pretty sure I justifiably pride myself on is knowing that everyone will have things they can teach you, and you're always going to find out that something you think you know turns out wrong - you just don't know what it is until you get there.   Just the bursting enthusiasm that comes with ADHD when you hit something that gives you dopamine dumps can come across like you think everyone else is wrong or don't matter. But yeah, I'm a software engineer by trade and also do tuning in weekends and 100% have long had a reputation for  quickly making connections when resolving problems or forming solutions that I've sometimes had to take people form a long walk from start to end to explain how I ended up where I did when it's seemed "too simple" when I've stated my initial case, and had the "WTF" type reaction when they've realised how much was actually considered haha.   My reward is that I get all the curly problems thrown at me.
×
×
  • Create New...