Jump to content
SAU Community

Recommended Posts

I've been recently reading up on the differences of between turbochargers and superchargers - interesting read I must say ;)

Now this question occurred in my mind:

Is it possible to stick both a turbocharger and supercharger into a twin turbo car (let say an R32 GTR 'cause I love them)?

If it were possible what would the benefits be?

Seeing as there would be turbo lag, would the installed supercharger cover for that initially (and once it kicks in, ;))?

Sorry, if a similar question was posted. I was too intrigued my hand couldn't stop typing :D

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/258601-two-kinds-of-turbo/
Share on other sites

stockymystock has an rb30 turbocharged and superchareged

can be done, costs lots of $$$, lots of custom work and changes

twin turbo is easier, cheaper, more normal

a good twin turbo setup would negate the require for super & turbo

as it would provide good average power, remember superchargers suck some power to give some power

its not like its free

sure a supercharger needs crank hp to run, but since it creates boost as soon as it starts turning, and feeds it straight back into the engine to create more power, the hp needed to run the sc is then accounted for. feedback cycle.

eg. engine 100hp

sc 50hp

sc boost power gain 100hp

total hp when you use the engine with sc = 100 - 50 + 100 = 150hp. net increase in power even though the sc takes 50hp, it gives back more almost immediately.

the energy is supplied by the additional fuel burnt as a result of the increased intake charge pressure. you wont experience any 'lag' from a supercharger

the power is not free, you pay for it in fuel. but you dont 'lose' any power from having a sc

if you can do fab work yourself and have the mechanical knowledge, it can be a cost effective option

of course it takes a specific application to require a super/turbo combination.

in track, drag, or most race applications, low end driveablity and torque down low is not usually a factor as gearing and driver skill is used to keep the revs in the powerband (top end of the rev range).

twincharging can be done relatively cheaply using aftermarket parts such as toyota factory superchargers.

unless you want something different there is probably an easier solution to lack of low end torque with a large turbo.

i would suggest a good ecu setup with anti-lag and the use of cheap t3/t4 based turbo chargers (as you'll probably have to replace it once in a while depending on your use of the anti lag).

or nitrous

Is it possible to stick both a turbocharger and supercharger into a twin turbo car (let say an R32 GTR 'cause I love them)?

Sure. There are a couple of aftermarket cars that have been twincharged, and Volkswagen has a production one.

Benefits are no lag at low RPM while getting more power down low thanks to the supercharger, and at high RPM you can enjoy the better efficiencies of a turbocharger.

The problem is getting it all to work together smoothly.

try looking at the twincharged s15 on youtube; was a fantastic watch and the results were fantastic.

sr20 yes but there was almost no lag so on an rb26 i doubt there would be any

are there any superchargers that disengage at a certain rpm???

So do turbochargers.

Technically yes, but in practice: they're sucking energy from waste gasses that are just being ejected out of the car anyway.

They do cause restriction, yes. but they don't suck raw shaft engine power

I believe the superchargers on the 4agze does that.It has a clutch on the blower drive much like an ac clutch

Yep.

I'm pretty sure the supercharged Merc engines have them as well.

They do cause restriction, yes. but they don't suck raw shaft engine power

And that restriction causes pumping losses. Stick a restriction in your exhaust, and see what happens to your power output. It's irrelevant whether that power "loss" has come from something attached to the crank, or something stuck in the exhaust. A power drop caused by an induction charger is still a power drop.

Its misleading to say superchargers "draw power to make power" as a pro against turbochargers, because the latter does the exact same thing.

Turbochargers are more efficient because they draw less power to give the same gain, but its not the free lunch some people make it out to be.

Edited by scathing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Strangely I noticed it either disappear later in the day, or not be present. I definitely noticed when I was crawling around that open wheel thingy entering the pits (that part was audible in car). Driving home and commuting around town for example, I didn't hear it. It's plausible that it was a brake disc or something still slightly in contact. The brakes absolutely felt BAD for the first couple of sessions, huge amounts of shudder and grinding as they got up to temp - And then I actually just forgot about it as the day went on/didn't notice it. The videos were from the morning when this was more present than the afternoon/drive home when it wasn't. I've asked around and got a variety of responses including handbrake shoe contacting hub, CV joints, CB tailshaft bearing as above, and clutch input bearing. I didn't test if it disappeared when clutch was in. I haven't noticed it in any of the other videos nor did I notice it when driving to that extent. More or less hoping the microphone at the rear license plate giving some kind of clue of 'something' but it looks like "spin stuff and see if you can notice it" is the way forward here. I could be smart and use the gopro mic and re-mount it to that location to see if the sound is still present at low speed actually. Sounds like a decent test whenver I have the CBF'ness to drive the car again. Given it's almost 40C for the day of the track day and the next 3 days after, the CBF is high. All I've done since getting home is unpack the car, remove the remnants of the lip and undertray and left it there. I was surprised how well the PMU Club Racers actually worked. The brake performance on the track was absolutely fantastic, best I've ever personally used, no fade whatsoever and the bitiness was almost too good, I was scrubbing more speed off than I needed to, but I also ended up infield when I started trying to scrape off ... less speed.... so...
    • Not really, no. Anything you would do is easily reversible.
    • I would like more noise related info for my truly uneducated guess  Does it do it at idle or when revving, clutch engaged, and disengaged? Does it only do it when the car is moving? I've heard "similar" noises from a clutch pack that left the chat room, and CV joints that have chewed themselves out But as Matt said, how's the yokes, tailshaft and centre bearing going after their last little issue Fingers crossed it is something simple  Weird noises make me cringe 
    • One other question, is there a chance that changing the idle speed can lead you down a rabbit hole and is the reason the tuner didn't touch it? Reason I ask is because if that's the reason the tuner avoided it then I probably shouldn't be touching it lol.
    • Pfft. As if I'd ever point a high pressure washer at my car.
×
×
  • Create New...