Jump to content
SAU Community

R33 GTS-t - reliability


Recommended Posts

$23k less than a year ago

fmic, boost, kit, zeal suspension, HKS exhaust sys, 77,000km..

No problems whatsoever.. i'm glad i didn't buy a heaps cheaper one, although at the time it was still a bit more than quite a few gts-t out there. Was a bit nervous at first, but after a few months i knew i had a pretty good example.

Link to comment
Share on other sites

All my wiring burnt out and started a fire in mine one day thanks to some VERY VERY dodgy gauge wiring. My advice - don't get one with a ton of aftermarket gauges fitted. Maybe even no aftermarket stereo. The effort on my car was certainly a bad home job, not professionally done. I've heard this is fairly common in Japan.

The rest of the car has been perfect. It had 100,000km (apparently :()on it at the time I bought it. Goes well and hasn't ever broken down.

I paid about $20K for mine 2 years ago (which was cheap at the time), so you might want to do what predator says and pay that bit extra for a good quality one, or go my way and hope it's a quality example.

Link to comment
Share on other sites

The effort on my car was certainly a bad home job, not professionally done. I've heard this is fairly common in Japan.

I gotta agree with this. I've seen plenty of cars here with some seriously dodgy aftermarket guage wiring - cables twisted together by hand and the like!

I personally would avoid cars with loads of extra gauges and cabling lying around the interior...

Link to comment
Share on other sites

got mine for $23K 2 years back, 94 model with 53,000 km.

only thing it had wrong with it was the wheel well was dented, easily fixed with a hammer and a bit of would, they must have hit a low pole caused nothing else had been panel beated or replaced!! bit of a bagain :(

Link to comment
Share on other sites

I bought it from a wholesaler in Brisbane. It was stock standard apart from the Nismo strut brace and brake master stopper, hks turbo timer and side skirts. Im the first owner in Aus.

Ive since put a set of 17" rims, type-m front bar, safc2, boost guage, bleed valve, 3" exhaust, stereo etc....maybe looking at selling it soon.

Link to comment
Share on other sites

23k for my 93 model with 80ks. Was relatively stock and didnt have much problems,except the timing was out.

But after i put some mods in,the engine started to wear out really bad,., ie.piston rings,., but that was my fault

anyway a good deal if u buy a nice clean standard one

Link to comment
Share on other sites

Hey,

Bought mine at the start of this year, imported and received it in late June/July.

94 GTST totally stock - $14.3k on road.

suspensions - $800

stereo - $1200

insurance - $2K

service - $150

Look on the guy in HSV I hosed the other day......priceless :)

There are many things which money can buy.........but nothing beats a skyline

So yeah, get one, they're great fun. I've had no problems with mine concerning reliability. Just invest in things such as a turbo timer etc etc and you should be fine

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...