Jump to content
SAU Community

Recommended Posts

hey got picked for a "random" drug test/alco test, and to make a long story short got defected, my exaust is to loud didnt evan messure it iwht a db metre, its a standard r33 series 1 exsaust then from cat 3" back to a 5" cannon,it had a silencer in the tip but i had it bashed out, and he looked under my bonnet and sdaid my fan shroud is to small and is ilegal, what do i do? try and pass it with a silencer, also i have a trust turbotimer, a greddy boost controller and a blitz infomation display all in the secon din pocket, are any of these ilegal?

Link to comment
https://www.sau.com.au/forums/topic/259276-defected-need-advice/
Share on other sites

set your turbo timer to 0 then they wont hassle you for that

pretty much make sure all your signals are working (breaks, indicators, lights, revers and number plate lights)

also make sure your wipers and squirters work

make sure that your tyres are good

it has to be over 11 cms from the ground at the lowest point (usually exhaust)

your exhaust will be fine, mine has no mufflers (only a cannon) and it passed last week with a bashed out cat :blink:

it has to be over 11 cms from the ground at the lowest point (usually exhaust)

100mm in WA. And it's only for solid items like the exhaust. Flexible items like mudflaps etc. are ok.

This pissed me off when I got done becuase the inspector told me of a recent Merc that was brought out from the factory and passed that had an 85mm clearance.

Typical..........

100mm in WA. And it's only for solid items like the exhaust. Flexible items like mudflaps etc. are ok.

This pissed me off when I got done becuase the inspector told me of a recent Merc that was brought out from the factory and passed that had an 85mm clearance.

Typical..........

500mm to bottom of the headlight , had a 32 pass that wasnt 100mm under car clearance

500mm to bottom of the headlight , had a 32 pass that wasnt 100mm under car clearance

That's probably another of their little tests. When I went over, there was a 100mm bump and the inspector said that if I scraped, I was too low.

He didn't measure to the headlights, he measured the eyebrow level and told me I had to put a 10mm block under the rear spring?!?!?!?!?!

What they'll pass you for depends on whether they got a root the night before.........

^ here here

when i was at the pits i was told it is 100mm for the lowest part of the car (does NOT have to be solid - ie. my bodykit was measured as it was lower than my exhaust)

WITH a car load of grown adults AND a full tank of fuel

that's my personal understanding, i got let off as i had adjustable suspension because they check that too, let off with a warning to get a permit for the suspension asap so if you have adjustable suspension that may work in your favour

Edited by hoony
100mm with a full car load as well.

My car was 100mm exactly with nobody in it, inspector passed me with a warning on that one!

HAHA... bloody inspector failed me even with 100mm. He says if there was 5 ppl in the car it will be less than 100mm. That was his reason for failing me. OH stock car! So good luck!

^^ Rock hard billsteins here mate :) Passed fine (5 ppl would probably drop it half a cm max.. lol)

The problem is its a STOCK CAR! If it was lowered or modified in anyway i would understand. Told him thats the build of the car, its lower than most car even with stock springs and suspension.

100mm in WA. And it's only for solid items like the exhaust. Flexible items like mudflaps etc. are ok.

This pissed me off when I got done becuase the inspector told me of a recent Merc that was brought out from the factory and passed that had an 85mm clearance.

Typical..........

the A series merc had a 85mm clearance where the oil sump was the lowest part of the car. This had a manufacturer warranty with it meaning that if anything happened to the oil sump, merc will have to fix it or give you a new one.

I was told it was a 100mm clearance from the lowest part of the car excluding mud flaps.

Do the simple things:

Degrease engine bay and gearbox.

Make sure car is as said 100mm of ground everywhere.

Headlights are 500mm of ground.

Put in silencer to exhaust.

Depending on which PITS you got they have different ways of test height. They usually drive over a speed bump. If it scrapes, too low. Pits have different height ones. Heard welshpool is 85mm and another one is 140mm

Fan shroud is just a way of getting you stickered cos u wouldn't know the regulations about it. Similar to tyres. How do you disprove that they weren't bald when the cop issued sticker. So have good tire depth. Gadgets aren't illegal as long as they are not inpairing vision of drive.

But yeh, stickers are a cops way of making it harder for you as a car enthusiast. And to scare people.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • $53.35 and a double din Pioneer head unit that I have...
    • Put a camera facing your dashboard so you can film the gauges. Head out to a straight but of road, and filming it as you go from a stand still at wide open throttle to as fast as you can/feel comfortable doing. Then film the dash board as you for example accelerate like normal onto a freeway. This will give us an indicator from Speedo of your expectation of slow, and will give us the rpm reading too to see if it's shifting. (Auto still has tacho from memory)
    • Buy yourself the cooling system pressure tester. Being able to pump it up, and have a gauge on it, AND have a cold engine makes it much easier / practical to diagnose. Additionally as the engine isn't running, you can listen for pin hole leaks as well as watching if pressure drops away. In addition, you can pressurise and while doing so, watch all the little rubber hoses. Some fail very brittle, and will just leak, while others can end up very soft and bulge. While a bulging hose isn't necessarily leaking, one of those small ones starting to stretch / expand in a bad way is an indicator that you'll be looking to replace that one soon   Depending on if this is a project car, or you'll be dailying it in the summer months would alter how I'd be most comfortable with driving the car and how I'd replace. If you're planning to use it as a daily, with no backup, I'd pull the engine, and replace all the external oil/water lines in one big swoop. At the same time do the timing belt, water pump, tensioners etc. Do not open the engine at all. We just want to replace all the things that are inexpensive as a single item, but a PITA when they go. By doing the above, you've made the car from a bunch of age related issues more reliable. If it's a project, and you like swearing while trying to reach into dirty hard to reach places to replace a single hose that may or may not be the leaky one. Just replace the leaking/bad ones as they need it. If it's a project and you'd rather swear at the car once and enjoy it as much as possible, then refer to the process I mentioned in how I'd want to do it if it were a daily. However, the approaches above do come down to how much spare pocket change you have. Pulling the engine and dropping over a thousand dollars on parts, may not be practical for you. Oh, if engine outing, I'd replace as many silicon/rubber inlet joiners as possible too.
    • Yeah, they're pretty dumb though...ie; they'll throw a solenoid error if the solenoid is dead, shorted, wiring is open circuit, or even if the driver transistor has failed (they can't self-diagnose much, they can only test inputs/outputs)... but if you wanted to try, I believe it's this protocol....(uses a long pulse indicator with short pulse counter)...    
    • Yeah I'll do what I can without taking off any major parts for now. If it becomes clear I won't get far with the engine in the car I'll have to think about the next steps. I am not too stuck on keeping everything 100% OEM, if there is better solutions, like converting most lines to braided with AN adapters, I'd rather do that than buy overpriced new "shit" parts.
×
×
  • Create New...