Jump to content
SAU Community

Recommended Posts

Hi All,

Ive had this anoying sqeak for the past week or so only notice it when im going slow and theirs minimal road noise (under say 40km/h). Tonight decided to investigate it a bit more. Ive worked out that when I push down on the Passenger front guard to compress/move suspension it makes the sound.

I removed the wheel and sprayed some inox on the any moving parts i could see to see if somethings just super dry or whatever and then put the wheel back on and had another push and the f**kers still their. :blink:

If i was to remove the coilover and completely remove all the suspension components lube them up and re install will I loose any camber or toe/alignment settings?

Any ideas?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/259315-anoying-sqeak-from-front-left/
Share on other sites

If i was to remove the coilover and completely remove all the suspension components lube them up and re install will I loose any camber or toe/alignment settings?

Any ideas?

Yeah, you'll need a re-alignment if you remove your coilovers.

I'd say it could be one of your bushes...camber, castor, or swaybar bushes.

I put this up in the stag section as well and their are two others that had the same problem.

For both of them they removed a bolt on the control arm pryed back the seal on the bush with a flat head screwdriver and sprayed some lube in each end and it shut the thing up.

Start uni late tomorrow so will give it a crack :P

haha no GF at the moment. But i do have a funny story...

Took a girl for a drive down to the bay a few weeks back to go for a walk around the place icecream and walk on the beach ect (early stages of getting in her pants ayy :P)

On the way down their on anzacs a black VE V8 commie of some sort pulled up next to us with 4 male occupants and the driver put down his window and said Ill race you for your missus. HAHA she WASNT impressed and put the window up almost immediately.

being used as a wager hahahah....

Best part was I was to busy laughing about it and completely missed the lights as the commie rocketed away.... haha

i think its a decoy from those commy drivers...

make you laugh so hard that you miss the lights and they can scamper away

lol

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From the pictures I have when doing the job the flywheel is the same diameter, I don't think they're playing weird tricks like putting weights at the outer diameter to increase flywheel inertia or anything like that. The OEM flywheel is definitely heavier, but it's not a huge difference. Quoted weight savings of the clutch is 2 kg so I can't imagine the flywheel being lighter than ~7 kg. Kind of regret not weighing it before the clutch went into the car but as far as driveability goes I have no complaints.
    • HKS trigger kit should be very easy to integrate with a Link. It's a 36-2 crank trigger. Hard part is finding the motivation to take off the timing belt and everything on the front of the engine to install it. You also need to cut out a hole in the oil pump housing so the sensor can read the trigger wheel. Changing out the cam sensor for a 24 tooth setup is probably good enough but as others have mentioned depending on what underlying assumptions are changed it becomes more of a problem. Reading the crank state off of the cam is an abstraction that works in the general case, but if you have an edge case it makes less and less sense. There is a GTX2860 gen 2 that can take a compact 5 bolt housing so it's direct bolt on but I'm not 100% sure of what's involved. Peak compressor efficiency drops off a bit on these turbos vs -5s, 77% vs 73% but you get way, way wider region of operation. The -5s have a really strange surge line in their compressor map that is all over the place. If you think the hot side on the -5s aren't open enough you can try the Tomei T550B turbos which a local tuner seems to be happy with:
    • i need a complete tail light for my R33 GTR if you have please let me know.
    • I need a great maintenance workshop around Idaho, if you know one please let me know..
    • Hello friends, i have a good friend in Canada that looking for a good condition 1993 GTR around him please if one or know someone around you that is willing to let it go please let me know so that i can inform him.....Thanks
×
×
  • Create New...