Jump to content
SAU Community

Recommended Posts

I have been told by my fabricator / tuner that in all likely hood, a twin 2860 -5 will probably surge ...

Application is bolt straight up to standard engine and standard manifold, aftermarket exhaust, injectors and all the small supporting mods ... 20psi ~ 340ish awkw.

Reasoning - both turbos will be pushing large amounts of air ... in doing so, they will fight against each other and surge / cause the boooof boooof boooof air pressure noise .... and the turbos will shiet themselves eventually...

Basically, any twin setup size that is 2860 -5 size onwards, will have this problem on a standard manifold/application...

Does any1 have any experience with this?

Does it sound right at all?

Edited by Phantom Snail
Link to comment
https://www.sau.com.au/forums/topic/260012-rb26dett-2860-5-surge-myth/
Share on other sites

  • 2 weeks later...

mythbusters ahoy!

there are two known occurances of surge that we usually refer two in the GTR twin turbo setup

1) compressor surging known and heard as "flutter" when coming on boost

this is a result of the pressure in the manifold going past the compressors effiency, ie the compress map says in the best scenario it can flowing at best 16psi of compression, but for some reason the manifold pressure is say 18psi so the compressors surge resulting in vl turbo style flutter on boost, ie: the compressors are out of effeiency and surging / erractic operation / wobble

any form of compressor surge is bad, can be fatal, and should be avoided/corrected at any cost

2) compressor chuffing / the turbochargers chuff when coming on boost / aka shuffling

this is usually caused by aftermarket pods and piping kits to the stock turbo's. basically the air reverbates and chops past the airflow meter, so it runs like a bitch.

this is common with say 2530s and custom piping and pods. not very common on stockers i dont think, but certainly possible

the std accordian style pipework reduces this by altering the path of airflow, when you replace with shiny smooth pipework, the problem occurs

if #1

compress surging, try lowering the boost, see if that helps

the compressors shouldnt surge under normal conditions

could indicate compressor failure, out of balanace or chopped wheels

again assuming the same problem occurs on say stock boost

if #2

try seperating the pods or putting a shitload of pipework between one of them or both them,

try like some good sized pool shop vacuum hose for one of both of the pods, try bending the pods intake pipes.

anything to alter the intake path of air to the compressor inlet snout

GTSS, HKS hard pipe kit, PFC djetro, 18PSI, 331RWKW, no shuffle at all

interesting, seeing that he's asking specifically about a different turbo... :D

2860-5, 340kw, no shuffle. Std airbox, greddy hard pipe kit, std BOVs.

when i bought my GTR, one of the things that sold me on my car was hearing the sweet sound of the turbos spooling, as ive said before im not a big fan of all the BOV, wastegate loud exhaust's noises etc, so when i got my car back was kinda gutted.

big turbo shuffle, BOV noises (even though its plumbed back) etc.

would some how building a box around the pods mask the noise, not that is any room!

just wanna here the -5s aye

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
    • I have a heap that i have collected if you want some authentic ones still. Pm me if your interested!
×
×
  • Create New...