Jump to content
SAU Community

F.s: R33 Veilside Body Kit And Bonnet

NGK
 Share

Recommended Posts

NGK Enthusiast

NGK

Posted
Posted (edited)

ok peeps ive had a change of plans and no longer need this stuff..

suits series 1 & 1.5 r33 2 door only!!

1: brand new complete veilside body kit.

front bar, rear bar, side skirts. $600 the kit, will not sep.

front bar only fitted once but not left the workshop

2: brand new STAGE 21 fiberglass bonnet.

imported from Japan, so its a good quality product. its been fitted once only but not left the workshop. does have one corner chipped off (about 5mm) other than that is a great bonnet..

$300

reason for sale: going back to steel bonnet to have tighter gaps with less aggressive front bar

to suit the new 2 tone paint job.

location: melbourne

ph: 0417522192 - mark

e5261.jpg

e6f11.jpg

e6541.jpg

bonnet.jpg

posta16332227022008007.jpg

posta16332127022008006.jpg

posta16332427022008009.jpg

Edited by NGK
Link to comment
https://www.sau.com.au/forums/topic/260057-fs-r33-veilside-body-kit-and-bonnet/
Share on other sites
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r34killa
      General interior R34 questions

      By r34killa · Posted

      Hi everyone, I'm generally new to DIY projects, and I've browsed this forum and watched a lot of youtube videos but still have a few questions   Firstly, how does spray painting interior hold up? in particular like vinyl parts, my current mode of thinking is to use methyl spirits to take off original paint, clean/prep well, light coats, no primer or clear coat    Secondly, what is recommended for the headliner and, for example (my car is a r34), the A-pillars which are some kind of other fabric material, do you think I would be successful at retrimming these? or would it be better to go down the blacking out via Dupli-Color Vinyl & Fabric Paint    Any other advice / tips / tricks for refreshing/modernising these interiors?    Thanks
    • D.s
      WTB-R32 gtst front bar-sydney

      By D.s · Posted

      As title says  Pm a photo with what u have  Type m style would be good As Hidding a thick front mount
    • Duncan
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By Duncan · Posted

      Just note that when trying to find a short in a globe power supply, it is best to disconnect the globe as it will allow current through to earth. With it unplugged it is easier not to get confused. Also with the r32 wiring, the high beam has 2 power supplies (one when you push the switch forward and the other when you temporarily pull it back; so if it is the high beam blowing you will need to trace both circuits
    • dyl33
      R32 gtst Center bearing (brand new)

      By dyl33 · Posted

      $75 Location: Gold Coast  Can post via Australia post
    • GTSBoy
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By GTSBoy · Posted

      That's a short. Find the short. It will be somewhere between that fuse and the headlight. Start by removing the plugs from the back of the headlight and dimmer switches, and measure resistance to earth. Supply side (power from the fuse) should have none. The other side should have resistance compatible with whatever globe(s) is there (which is relatively easy to say for a normal globe, perhaps not as easy to say for LEDs). Anyway, if you have very low resistance, you defo have a short. Then you just have to run the wiring like you're running the bowel of a dog (on the operating table) that has swallowed something it wasn't supposed to.
×
×
  • Create New...