Jump to content
SAU Community

Recommended Posts

Item: Purvis Eureka Kit car

Location: Sydney

Item Condition: Good

Reason for Selling: If it sells it sells if not i keep it. Don't really have time to fix at the moment.

Price and Payment Conditions: $5,500 WILL NOT DROP ANY LOWER, Not taking parts off to lower price, you take the car you take it all.

Extra Info:

Motor is apart, its a Vw 1500cc.

1.5" Bugpack Megadual Exhausts

Chrome Air filter

Lumpy Camshaft

Honed cylinders

EMPI Oil Cooler

Lexcen headlamp Covers - Bubbles in right side of Tint, will fix. Tint 35%.

Lexcen Smoked Side Windows - Custom made $400 new

Lambo Air Intake scoops

70's style side mirrors

Hydraulic Rams for Roof lift - New seals $100

Hydraulic pump for roof lift

Type R Wheel

Quick Release Boss Kit

Autotechnica Pedal Pads

Chrome Shifter

Monza Gearboot

Full Set of VDO Gauges

14" Bathurst Globe Rims (F:205/70, R:235/60)

VW 1500 4spd Transaxle - Has been flushed out

Valeo Heavy Duty Clutch + stock clutch

Valeo Pressure Plate + Stock P/plate

Short Shifter

Bilstein Gas Shocks

Rebuilt Front calipers

Brembo Front disk Rotors

Rebuilt Rear Drums

New Master Cylinder

Car Weigh's 780kg, with a nice paintjob and a 12A rotor it would go pretty good. New Floorpan has been welded in & painted.

All interior trim is there, wiring works, have all previous rego & engineer certs.

Car needs:

Motor: Either this one rebuilt - $1-2k, $200 ebay one or even your own motor you want to stick in.

Seats: Will Need to be from a smaller car - $?

and Rego: Car complies with all ADR's

Paint

For $3-4k you have a car worth $15k

Pictures:

Yep

Contact Details:

Pm me

In about two months time if it does not sell i will be putting in a Forged Vdub motor(ready for turbo), as of then price will be $8,500

post-29561-1236514395_thumb.jpg

post-29561-1236514522_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/260205-fs-purvis-eureka-f4/
Share on other sites

  • 2 months later...

Bump, motor has been rebuilt to standard spec(by my old man) but has not been put into the car or started. Price is $6,000, will also trade for a more expensive car + cash(upto $5000) your way if necessary. Prefer R33 Non turbo.

  • 2 weeks later...
  • 2 weeks later...
  • 11 months later...
  • 5 years later...
  • 1 month later...
Guest
This topic is now closed to further replies.


  • Latest Posts

    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
    • How does this compare to the internally gated g25-550 in terms of power production at same psi and spool
    • Did you find that your voltage of the battery wasn't where it's normally supposed to be? for example on my r34, it's at 14.5v when running after a few seconds, but I noticed when I had a rough start and it initially wasn't idling correctly, the voltage on my triple gauge cluster was showing lower than usual. Seems like the alternator is starting to crap itself
×
×
  • Create New...