Jump to content
SAU Community

Recommended Posts

its quite hard to get an estimate for a price of a tune because there is an endless continuim of tuning quality. at the end of the day your better going to a reputable tuner who you trust not to rip you off.

Also another point is that tuners save the calibrations of EVERY car they tune along with a full set of notes, so as much as youd like to believe your getting a tune from scratch, often tuners will find a previous calibration and start from there, which saves time and hopefully money.

I cant say ive heard of microtchs going out of tune, sounds strange. perhaps one option would be to save your calibration on your computer so you can reload it to the microtech everytime the car doesnt run right.

also its a good idea to run an O2 sensor, especially a wideband, so the computer can run closed loop, as its often more economical and smoother running when cruising

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

N1GTR would you mind enlightening me on how that was possible?

And yeah had it been me (who wouldn't have gotten a Microtech in the first place), Id've gotten it tuned with an 02 sensor of some type. Apparently they can be tuned to be as economical without though, but I'm not sure.

Edited by bozodos
its quite hard to get an estimate for a price of a tune because there is an endless continuim of tuning quality. at the end of the day your better going to a reputable tuner who you trust not to rip you off.

Also another point is that tuners save the calibrations of EVERY car they tune along with a full set of notes, so as much as youd like to believe your getting a tune from scratch, often tuners will find a previous calibration and start from there, which saves time and hopefully money.

I cant say ive heard of microtchs going out of tune, sounds strange. perhaps one option would be to save your calibration on your computer so you can reload it to the microtech everytime the car doesnt run right.

also its a good idea to run an O2 sensor, especially a wideband, so the computer can run closed loop, as its often more economical and smoother running when cruising

i know i was getting a tune from scratch. first gtr on a wolf v500 that my tuner/mechanic had done.

but you are correct. and in a lot of cases this is a very good idea. it's basically the same as having a base map like a power fc etc.

Its not a good idea to tune with 02 sensor feedback on, as it will always give you varied results and the ECU will be constantly correcting etc, its nasty, if you know how to tune, you can get good economy and smooth cruise without closed loop.

N1GTR would you mind enlightening me on how that was possible?

And yeah had it been me (who wouldn't have gotten a Microtech in the first place), Id've gotten it tuned with an 02 sensor of some type. Apparently they can be tuned to be as economical without though, but I'm not sure.

If i could remember, i would

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey all,   I’ve got an RB25 with a trigger kit that includes a crank wheel, and I’ve hit a wall trying to sort a timing belt tracking issue. The belt either rides right on the edge of the cam/crank pulleys or walks slightly forward once the engine starts. It tracks okay-ish for a moment, then creeps right to the edge—and honestly, it’s stressing me out.   I’ve spent hours removing and reinstalling the belt, double-checking everything:   Tensioner setup is good, checked multiple times Idler pulley and washers are all in the correct places Followed the RB25 timing procedure step-by-step     The only thing I changed was the rear crank washer—I swapped the OEM one for a Neato version, and it made things worse. The belt now sits even more forward than before. I’m beginning to think the crank trigger wheel itself (from the trigger kit) is the issue—poor design or slightly off dimensions.   What’s strange is that with the previous belt setup, it actually ran fine for a couple of years—around 4,000 to 5,000 miles, even with hard driving and high RPMs. But even then, the belt was always riding right on the edge, and I know that’s not ideal or safe long term.   At this point, I’m debating whether to:   Machine a few mm off the crank trigger wheel to bring it back in line, or Replace it entirely with a better-designed unit     Only thing is, I already have the Cherry Hall sensors, bracket, etc.—I just want to replace the wheel only, not the entire kit. Anyone know a brand or supplier that sells just the crank trigger wheel on its own?   Would really appreciate any feedback—especially from anyone who’s run into this exact issue and found a reliable fix.   Thanks in advance.
    • Hi...a little refresh. Is Nistune gonna be enough to run BoV? Or do i need some proper ECU? 
    • Yep that's pretty much what I want to see. Racecars that look and sound like the Group A but with newer tech underneath to make them faster and safer. I'm sure there's enough VK-to-VN commodore, E30 BMWs and Foxbody mustangs shells around to make up a decent number of cars with hopefully a couple of sierras, rx7 and R31s in there too. 
    • Contact Jessestreeter.com/Skevas Racing/JustJap for a new r34 rb gearbox or go a cd00# conversion. No point playing with unknown condition gearboxes.
    • Such a shame places like Amaroo Park have been redeveloped, smaller tracks always make for good racing. Cheers for sharing @PranK there's some good Lakeside video's too. Its so hard with older the cars as parts are so rare and everything was made for a particular chassis at that point in time. Even the V8 Supercar Blueprint era cars are all different between each chassis within a team as they learnt things and made improvements. The COTF cars between each Chassis builder is different too especially motor/oil systems/intakes. The Group A stuff is worth so much too especially chassis with good history. The only way to do it would be composite panels and similar engine drivelines to the original cars. Ford sierra running Focus RS driveline, Commodore running a short stroke LS/LT or a Falcon with coyote and a H Pattern dog box. Could use a standard ecu across all models with a Torque Map and DBW for parity which is not even used in Supercars currently. Hell a TCM is almost a full chassis car these days and the suspension is not even close to standard style in the front running cars.  
×
×
  • Create New...