Jump to content
SAU Community

Automatic Power Button Light Flashing

SkyHi_33
 Share

Recommended Posts

SkyHi_33 Mentor

SkyHi_33

Posted
Posted

Hi guys, I've noticed lately that sometimes when I start the car up the power button light flashes 16 times. The button itself is always set in the middle, I don't bother with it.

The car shifts fine and haven't had a problem with it except a couple times it wouldn't shift up until around 4-5,000 rpm when it was really cold.

Anyone know what the flashing means? I'm taking it for a service and shift kit install soon but would like to know what the deal is before i do it.

Cheers!

2LV8ETR Mentor

2LV8ETR

Posted
Posted

See if this helps..

Enter the auto transmission diagnostics mode:

  1. Have the car at normal temperature in Park with the overdrive on
  2. Start the engine the power light will go out after 2 seconds
  3. Turn the ignition off
  4. Move the selector to Drive (you may have to use the push button release)
  5. Overdrive off
  6. Wait 2 seconds, and turn the ignition on
  7. Wait 2 seconds and move the selector to 2
  8. Overdrive on
  9. Move the selector to 1
  10. Overdrive Off
  11. Press the accelerator fully and release

Auto transmission diagnostics codes:

The error codes are flashed out using the Power light on the dashboard (R32) or the Power / Snow button (R33). The sequence starts with one long flash. If everything is OK, this will be followed by ten short flashes. Errors are indicated by a long flash in the sequence of short flashes.

1st flash longer Revolution sensor shorted or disconnected

2nd flash longer Speed sensor shorted or disconnected

3rd flash longer Throttle sensor shorted or disconnected

4th flash longer Shift solenoid A shorted or disconnected

5th flash longer Shift solenoid B shorted or disconnected

6th flash longer Overrun clutch solenoid shorted or disconnected

7th flash longer Lockup solenoid shorted or disconnected

8th flash longer Fluid temperature sensor is disconnected or the control unit power source is damaged

9th flash longer Engine revolution sensor shorted or disconnected

10th flash longer Line pressure solenoid shorted or disconnected

All flashes the same with no long start flash - Battery voltage low, has been recently disconnected or control unit has just been reconnected

SkyHi_33 Mentor

SkyHi_33

Posted
  • Author
Posted

Ahhhhh i think i might know why, had to replace my battery not long ago to pass roadworthy... I'll check out the diagnostic feature though and see whats up.

Thanks so much for this!!! :cool:

  • 12 years later...
Haji Newbie

Haji

Posted
Posted
On 11/03/2009 at 3:16 AM, 2LV8ETR said:

See if this helps..

Enter the auto transmission diagnostics mode:

 

  1. Have the car at normal temperature in Park with the overdrive on
  2. Start the engine the power light will go out after 2 seconds
  3. Turn the ignition off
  4. Move the selector to Drive (you may have to use the push button release)
  5. Overdrive off
  6. Wait 2 seconds, and turn the ignition on
  7. Wait 2 seconds and move the selector to 2
  8. Overdrive on
  9. Move the selector to 1
  10. Overdrive Off
  11. Press the accelerator fully and release

 

Auto transmission diagnostics codes:

The error codes are flashed out using the Power light on the dashboard (R32) or the Power / Snow button (R33). The sequence starts with one long flash. If everything is OK, this will be followed by ten short flashes. Errors are indicated by a long flash in the sequence of short flashes.

1st flash longer Revolution sensor shorted or disconnected

2nd flash longer Speed sensor shorted or disconnected

3rd flash longer Throttle sensor shorted or disconnected

4th flash longer Shift solenoid A shorted or disconnected

5th flash longer Shift solenoid B shorted or disconnected

6th flash longer Overrun clutch solenoid shorted or disconnected

7th flash longer Lockup solenoid shorted or disconnected

8th flash longer Fluid temperature sensor is disconnected or the control unit power source is damaged

9th flash longer Engine revolution sensor shorted or disconnected

10th flash longer Line pressure solenoid shorted or disconnected

All flashes the same with no long start flash - Battery voltage low, has been recently disconnected or control unit has just been reconnected

Hi just had a similar problem to yours when I did my sub but the only prob was I could not go up past 3 gear I checked the power and snow switch it was not pluged in I just plugged it in and it was fine again also when they dyno these cars they disconnect the power and snow switch to stay in 3 gear. I hope this fixes it for you to 

  • 11 months later...
datsunbelievable Newbie

datsunbelievable

Posted
Posted

didn't answer question what does it mean power button flashes one long sixteen short and the car only selects third gear like it is in failsafe mode

 

  • 2 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ggub
      WTB RB25 Gearbox NSW / central west

      By ggub · Posted

      Agree with Rob. I recently did mine and replacing with a brand new unit made the most sense compared with rebuilding my existing gearbox.
    • GTSBoy
      Rb25 trigger kit and timing misalignment

      By GTSBoy · Posted

      Are you suggesting that the kit did a cheap and nasty job of just jamming the wheel in between other things and caused the misalignment? I mean, we normally do this with an integrated crank trigger wheel, not something bodged on. It's not 1995 any more.
    • joshuaho96
      R-chassis INNER tie rod torque spec?

      By joshuaho96 · Posted

      I mean, given the number of BMWs you own their tolerance for improper torque is rather low. The number of torque + angle spec bolts and non-reusable bolts in one is nuts.
    • joshuaho96
      Question about BoV on RB25DET NEO

      By joshuaho96 · Posted

      Atmospheric vent requires something that doesn't use a MAF for load. You would need a standalone ECU for that.
    • drifter17a
      Rb25 trigger kit and timing misalignment

      By drifter17a · Posted

      Hey all,   I’ve got an RB25 with a trigger kit that includes a crank wheel, and I’ve hit a wall trying to sort a timing belt tracking issue. The belt either rides right on the edge of the cam/crank pulleys or walks slightly forward once the engine starts. It tracks okay-ish for a moment, then creeps right to the edge—and honestly, it’s stressing me out.   I’ve spent hours removing and reinstalling the belt, double-checking everything:   Tensioner setup is good, checked multiple times Idler pulley and washers are all in the correct places Followed the RB25 timing procedure step-by-step     The only thing I changed was the rear crank washer—I swapped the OEM one for a Neato version, and it made things worse. The belt now sits even more forward than before. I’m beginning to think the crank trigger wheel itself (from the trigger kit) is the issue—poor design or slightly off dimensions.   What’s strange is that with the previous belt setup, it actually ran fine for a couple of years—around 4,000 to 5,000 miles, even with hard driving and high RPMs. But even then, the belt was always riding right on the edge, and I know that’s not ideal or safe long term.   At this point, I’m debating whether to:   Machine a few mm off the crank trigger wheel to bring it back in line, or Replace it entirely with a better-designed unit     Only thing is, I already have the Cherry Hall sensors, bracket, etc.—I just want to replace the wheel only, not the entire kit. Anyone know a brand or supplier that sells just the crank trigger wheel on its own?   Would really appreciate any feedback—especially from anyone who’s run into this exact issue and found a reliable fix.   Thanks in advance.
×
×
  • Create New...