Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

It’s around a 15% driveline loss.

So say 255awkw + 15% loss (38kw) = 293rwkw = 392rwhp

Which is about right for a standard N1.

@super coach tristan: tried a new grip tonight and got 51 with a strike rate of ~210 :blink:

Also got about 2 dozen stumpings and catches behind the stumps and a few wickets bowling. Good night (y)

To break it down more, rwkw to flywheel kw is roughly x1.33

so, 293rwkw x 1.33 = 389FLYWHEEL KW

Both post's above are rough, everyone has different veiws on loss and conversion rates

Maybe all these while the 300kw I had in mind was rw not aw. But the fact that the car feels lighter/smoother really surprises me. 1st gear used to hit limiter at 60-70km/h now it goes up to 80+. Amazed.

A stock N1 will never make 300awkw, unless the dyno is happy, or you tell the tuner to input 300awkw on the graph lol.

Your car is very healthy and is on par - What else is done to it?

BUGGA!

Went for the tune today and made 255awkw... I wonder whats the difference between rwkw and awkw... =(

But the car feels soooo much smoother now.

Wooooo good shit

Ok, the list is as below

1) Trust Ti-R exhaust

2) HKS Front Pipe

3) Apexi Power FC

4) Apexi Boost Controller Kit

Thats all. Everything else is stock. 1.15bar I think (on the pfc hc). Cant get it to hold 1.2bar. No engine mods. Injectors are max at 90%.

Glad to hear the tune is good Brandon, who tuned it for you?

They must have lifted the rev limit a bit :blink:

Gavin Woods @ Autotech. Shit loads of GTRs... oh and 1 Tommy Kaira 32 (dont know real or not)

Ok, the list is as below

1) Trust Ti-R exhaust

2) HKS Front Pipe

3) Apexi Power FC

4) Apexi Boost Controller Kit

Thats all. Everything else is stock. 1.15bar I think (on the pfc hc). Cant get it to hold 1.2bar. No engine mods. Injectors are max at 90%.

Sort out why it's not holding more boost

- Get a better fuel pump

- Throw in some larger injectors

- Get a good set of cam gears

Spend more time on tuning and you will have a friggin quick car..

Your lack of boost.. They're N1's even 1.2bar is tame... and lack of fuel is why you only got 255awkw. IMHO, with the above and a very good tune you should get up around 280awkw, if you run more than 1.2bar..

If I'm ever gonna get it tuned again, I'll try Matt Spry.

Both Gavin and Matt gave me a good impression when I called comparing to the others.

Sort out why it's not holding more boost

- Get a better fuel pump

- Throw in some larger injectors

- Get a good set of cam gears

Spend more time on tuning and you will have a friggin quick car..

Your lack of boost.. They're N1's even 1.2bar is tame... and lack of fuel is why you only got 255awkw. IMHO, with the above and a very good tune you should get up around 280awkw, if you run more than 1.2bar..

He reckon its restriction. Or maybe injectors (he's not comfortable running higher than 90%). Or might be the boost controller (I've heard the kit doest hold boost very well after 20psi)

If I'm ever gonna get it tuned again, I'll try Matt Spry.

Both Gavin and Matt gave me a good impression when I called comparing to the others.

Don’t get me wrong, Gavin knows more about Nissans than most people – however to cut a VERY long story short, I bought a second hand Q45 throttle body from a wrecker, unknown to me at the time the wrecker swapped the TPS unit for a ca18 unit, which meant the car wasn’t tunable… My car was with Gavin for a full day and he couldn’t find what was wrong with it.

I took it to Matty and he found within 5 minutes that the TPS had been swapped over, we put the correct Q45 TPS in and had it tuned…

I know where I will continue to keep going back

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...