Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

always wanted one but if I get a new helmet it will be for when I get my bike and the simpson ones aren't legal for road use. The haven't had the required testing to be standard compliant...

@Colin: bike helmets are allowed under the current regs, as long as they meet AS1698. I use one.

BUT as Josh has said, they are not rated for the same kind of impacts as motorsport helmets. A new helmet for me has been long overdue, I guess that makes me a muppet :thumbsup:

I have been trying to track down solid info on what the requirements are changing to. I beleive they are dropping AS1698, and possibly a lot of the other older standards as well, and requiring a HANS device. I'm not going to buy a helmet until I know it will meet the new regs.

Best fitting helmets I've ever tried. So light aswell. I reckon my next helmet will be a Shoei helmet. Mum n Dad have both got Shoei's and they're great.

I thought they changed the regs so they had to be compliant with an AS/NZ code not just the AS one. Not sure will have to do a little research

I've got a couple of road bike helmets. I think they may be out of date. BS if I cant use them they're legal on the road so why not down a drag strip...

You can.. If they are in date.

at an event, you might as a road helmet isnt anything like a moto-x/dirt bike helmet.

at a CAMS event, thats a whole other story. They can ask you to go home with a JAP cage if they wish.

BUT as Josh has said, they are not rated for the same kind of impacts as motorsport helmets. A new helmet for me has been long overdue, I guess that makes me a muppet :thumbsup:

I'm talking moto-x/dirt bike.

I am lost why people why people wear these

O

I have been trying to track down solid info on what the requirements are changing to. I beleive they are dropping AS1698, and possibly a lot of the other older standards as well, and requiring a HANS device. I'm not going to buy a helmet until I know it will meet the new regs.

The problem is, is it going to be all across the board - ANDRA/CAMS/AASA :thumbsup:

fookers the lot of them

I'm talking moto-x/dirt bike.

I am lost why people why people wear these

O

people already have them from when they did mx - so they figure they might as well get good use out of them while they are still learning - until they decide they want to get more involved, and then get a proper helmet..

or is that just me and dave?

people already have them from when they did mx - so they figure they might as well get good use out of them while they are still learning - until they decide they want to get more involved, and then get a proper helmet..

or is that just me and dave?

And every other Ignorant drift rat...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...