Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

has potential then

So remember it when the zombies hit the fan.

Speaking of hitting the fan have you seen that zombie flick where the hero straps a lawnmower to his chest and walks through a mass of them? It's pretty awesome.

evenin' gents

Whats the consensus on zombies and razor/barb-wire?

Also; seen this before?

http://www.urbandead.com/

Doesn't it tangle them up for a bit ?

Signed up :thumbsup:

Forgots to tell you John there are three of these control rooms. This one here, the one in the valley and one in the centre of brisbane. All have generator backups and secure doors. The one in the valley doesn't have windows on the door and is three floors up.

I'm still unsure of those plastic hats though... I think they'll cause more harm than good.

The one you're at is probably the safest, there's less population out there, and the roads are much more open.

I'm still unsure of those plastic hats though... I think they'll cause more harm than good.

The one you're at is probably the safest, there's less population out there, and the roads are much more open.

we could throw them at the zombies and then use the rifles to shoot at them like ducks at a side show.... *bang* *ting* zombie turns and repeat. :thumbsup: Could be fun for hours.

The glass also worries me slightly... But I guess it's hardcore soundproof double paned thick shit huh?

Not sound proof. Its the non shatter stuff though with metal in it.

Joined... think I'm already dead though. Was a bit over eager using up my action points ... eep

You and me both :thumbsup: Can we join forces and f_ck shit up ?

You and me both :thumbsup: Can we join forces and f_ck shit up ?

Well... I don't have any points... so it probably wouldn't let me join my own dick with my hand at the moment... let alone join forces with someone

Well... I don't have any points... so it probably wouldn't let me join my own dick with my hand at the moment... let alone join forces with someone

Well you could always try the dick to hand move. I've heard its quite effective.

i guess so!

ah beer. isn't it amazing you can't just have one. like a coffee or a can of coke you have one and think thats enough for me. Beer you think i'll just have another one and another etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
×
×
  • Create New...