Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I had a feeling I was up shit creek.

When my womang suggested they move in I flat out said no straight away because I knew what she was like. Sam (missus) is one of those people that gives everyone a chance and then when they f**k up she'll give them a couple of hundred more. It's one of those situations where we all knew it was her, we confronted her about it and she got all shitty and started crying and acting all innocent. She's good at what she does put it that way. I remember one day she was standing out on my balcony on the phone to her Nanna trying to get her to send her money for rent by the sounds of it Nanna had an idea that her boyfriend smoked the green prawns, girl kept lying to her Nanna saying how noone in the house does drugs ever etc. Felt bad for the old bag for a second.

Would have kicked them out sooner but I was on less money than I am now and no way I was paying $190 for rent a week.

Edited by hylian

Legally? Nothing sorry dude.

Other avenues?

1. Provide John with mole's address

2. ???

3. Profit

HAHAHAHA I lol'd

Man that does suck...... I would've kicked her out sooner and found replacement tenants. I know it's not always possible though...

just throwing it out there. baskins was good tonight

Needed more gutter scraping and foot crushing though.

Edited by sneakey pete
  • Like 1

Morning!

Final day of my current job today.

Trying to figure out best possible early exit strategy. Thinking "Here's my keys, bye!" shortly after arriving and then peeling out in a cloud of blue smoke as I laugh maniacally. Suggestions?

Morning!

Final day of my current job today.

Trying to figure out best possible early exit strategy. Thinking "Here's my keys, bye!" shortly after arriving and then peeling out in a cloud of blue smoke as I laugh maniacally. Suggestions?

STL is definitely required.

Hahahaha sounds like a plan..... I'm not sure if you're ok with burning that bridge yet or not though?

Morning Mangs,

TFIF.

My epic internet hax has been shut down :(. I need to try not to swear in any of my posts now or I'll get this site blocked again...

Epic Tale

TL;DR

Naah seriously, legally I think your boned. Really shouldn't have let her get away with so much, and your missus should definitely not have just paid her for all the sh*t she left behind. In fact, I would have tried to charge her a 'disposal' fee for it all.

I want ice cream farken...

Approved

instead I am still writing a job application >_< and not very sucessfully I might add

Not Approved

Other avenues?

1. Provide John with mole's address

2. ???

3. Profit

I like this plan.

having a trial with dead as the punichment...

I was going to pay you out for that. But then I read this:

PS> as of 7pm tonight Ive done 69hours of work since 6am Monday morning...

And decided to forgive you.

just throwing it out there. baskins was good tonight

+11ty

Morning!

Final day of my current job today.

Trying to figure out best possible early exit strategy. Thinking "Here's my keys, bye!" shortly after arriving and then peeling out in a cloud of blue smoke as I laugh maniacally. Suggestions?

Meatspin?

STL is definitely required.

+1

Meatspin?

That's something I hope to never see again. Scarred for life.

German club next week mangs? I can take 4 in my car. Tuesday or Wednesday is good for me.

Edited by hylian

Trying to figure out best possible early exit strategy.

You could go with the "dump and burn"...

There are two possible interpretations;

1. Shit your pants and have to go early to clean your self up... (highly embarrassing but effective)

2. Walk into the boss's office and pull your pants down crouch on his/her desk and dump a chirly whirly in the middle of his/her desk and then "burn" aka run away quickly... (very funny & highly effective)

I was going to pay you out for that. But then I read this:

And decided to forgive you.

Oh i feel the love... gtg work time now... bye

That's something I hope to never see again. Scarred for life.

That's what she said.

German club next week mangs? I can take 4 in my car. Tuesday or Wednesday is good for me.

Keen. Can't do tuesday though (cricket).

Oh i feel the love... gtg work time now... bye

That's what she said.

5 skylines, an XF and an AU all pulling statics in the car park?

I'll bring my coon out as well, then well have a BA, the LSD is ford quality and only spins one wheel though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
    • I was more thinking so it doesn't flop around as much rather than for rotating it. Once you have the balance right, it should rotate well enough, depending on how much resistance there is on the pivot. I think you said the pivot point was on a bearing though didn't you?
×
×
  • Create New...