Jump to content
SAU Community

Recommended Posts

Also referring to your email. Your stock OP6 Neo turbo only made 180rwkws on 14psi which that should be way over 200rwkws any where else.

a stock turbo'd rb25 making "way over 200rwkw" on 14psi... stao, whatever you are on can you pls organise me a pound? ;)

also trent's dyno with the appropriate correction reads the same as a dyno dynamics, my car has backed this up on 3-4 dyno's now

Well my stock NEO turbo made 214rwkw on 11.5 psi... dynodynamics... That's a LOT better than 180...

And given my stock R33 RB25 series 1 turbo made 192rwkw on 11psi on the SAME DYNO, I'd say that the NEO turbo should clearly be making more than 180rwkw.

Your definitely not going to lose 150hp through the drivetrain. More like 50 - 80 max.

So you really should be seeing an easy 260rwkw from this turbo, which is more like 350-360rwhp.

I have definitely got faith in Stao's products for the outcome he advertises them to produce, and his customer service is near second to none. You should definitely take him up on the offer of swapping his result proven turbo with yours, it will rule out ANY further question in the turbo itself. Like Stao has already told you, its not impossible that the turbo is faulty however it is far more likely that you have another problem somewhere else. I fully support Stao on this notion, and feel you may need to engage another workshop (after you have swapped turbos with him).

Can I ask what dump pipe you have on the car? Direct from the turbo to the cat, who makes the item and can you take a photo?

Fair enough, just a thought.

Looking forward to Stao's results with the turbo today. I am using a Tomei bellmouth dump/front pipe, I'll try to get a photo.

OK here's the post i started last page and got interrupted.

Hanaldo, hang in there! Take Stao up on his offer to send you a working tested turbo, swap it over yourself. drive it in to the dyno and get it tuned. If there aren't any more problems, and the tune is half done already then it shouldn't take more than 2 max hours on the dyno.

As for the power, I have an ATR43G2 .82 making PULP 270rwkw with boost dropping down to 15psi, E-Flex making 290rwkw with boost dropping down to 13.5 psi. I didn't even bother with setting my boost controller up on E-Flex to hold it higher...

All on a Dyno Dynamics Dyno.

And about your statement about buying this turbo for it's bolt on and concealiability. Here's a couple of pics of my engine bay. Remember this is a 290rwkw engine bay.

post-62296-0-81799200-1301608724_thumb.jpg

post-62296-0-74894200-1301608737_thumb.jpg

post-62296-0-16451100-1301608748_thumb.jpg

So yes you can make this turbo look very stock.

Well done on the engine bay, looks very stock indeed.

Yep, if I can make 167rwkw @ 7psi with a 2IU, and my friend made 200rwkw @ 12psi with his OP6...there is something else amiss here.

Yep, if I can make 167rwkw @ 7psi with a 2IU, and my friend made 200rwkw @ 12psi with his OP6...there is something else amiss here.

As I said, not too worried about the number, it's just a number. My power curve on the stock turbo was fine.

When my car had the stock turbo it was tuned on Hyperdrives old dyno. Their dyno was known to read 20-30rwhp lower than all other dynos in the area, so the power figure would have been about right. Since I have had the new turbo, Hyperdrive haven't tuned my car with their own dyno.

And given my stock R33 RB25 series 1 turbo made 192rwkw on 11psi on the SAME DYNO, I'd say that the NEO turbo should clearly be making more than 180rwkw.

My R34 hit 182.7kw at 8psi untuned .. should be interesting to dyno again with a 10psi actuator fitted ..

OK here's the post i started last page and got interrupted.

Hanaldo, hang in there! Take Stao up on his offer to send you a working tested turbo, swap it over yourself. drive it in to the dyno and get it tuned. If there aren't any more problems, and the tune is half done already then it shouldn't take more than 2 max hours on the dyno.

As for the power, I have an ATR43G2 .82 making PULP 270rwkw with boost dropping down to 15psi, E-Flex making 290rwkw with boost dropping down to 13.5 psi. I didn't even bother with setting my boost controller up on E-Flex to hold it higher...

All on a Dyno Dynamics Dyno.

And about your statement about buying this turbo for it's bolt on and concealiability. Here's a couple of pics of my engine bay. Remember this is a 290rwkw engine bay.

So yes you can make this turbo look very stock.

Yeah who cares if the compressor cover is not factory with that airbox and scoop, you wouldnt be able to see it, nor would a cop bother after seeing it. Nice work! I gave up on trying to get the custom metal intake to fit the airbox nicely.

Yeah who cares if the compressor cover is not factory with that airbox and scoop, you wouldnt be able to see it, nor would a cop bother after seeing it. Nice work! I gave up on trying to get the custom metal intake to fit the airbox nicely.

They will pick you up on it with a defect inspection though.

There's pod filter under the air box... which has almost no plastic left in the bottom of it :)

Of course if they go looking hard enough you'll always cop a defect, but my thoughts are keep it looking stock enough to give them less of a reason to go looking any further...

sorry to thread hijack Stao

That is why I don't see the point of a highflow unless it retains stock rear and front covers. if you are going to change one, might as well just get a full garret turbo and hide that as a low mount.

as soon as you go over the stock AFM limit and go Z32 it all becomes a bit pointless anyway doesn't it?

for the picky bastards who want to do ya on something, they will right?

Details please! Never heard of it!

Really it's custom, what I said before is probably a bit misleading. It was designed using a Tomei Expreme GTR dump as a model, so the dump section looks almost exactly like a Tomei dump pipe but made to fit an RB25 turbo and is 3" all the way through from the bellmouth. From there back it is a straight cut pipe to the cat. All one piece.

Made by Kermit :D

as soon as you go over the stock AFM limit and go Z32 it all becomes a bit pointless anyway doesn't it?

for the picky bastards who want to do ya on something, they will right?

It's all just a gamble on how cluey and screwy your cop is. If they really wanted to screw you over, they would pull off the pipes and see that you don't have the standard comp wheel. It's all about how much you think you can get away with. The more you stick in there, the more power you get, but the worse it's going to be when/if you get defected for it all.

as soon as you go over the stock AFM limit and go Z32 it all becomes a bit pointless anyway doesn't it?

for the picky bastards who want to do ya on something, they will right?

Change the pink sticker to a green sticker, that is all they can check and almost no one knows that is the difference.

It's all just a gamble on how cluey and screwy your cop is. If they really wanted to screw you over, they would pull off the pipes and see that you don't have the standard comp wheel. It's all about how much you think you can get away with. The more you stick in there, the more power you get, but the worse it's going to be when/if you get defected for it all.

It's not really because I have never ever heard of a defect station removing your entire intake piping to check the comp wheel size, plus I'm fairly sure nissan don't put the specs in a workshop manual so they would have no reference and hence no reason to fail you.

Edited by Rolls

1. Undo the E-clip on the wastegate arm (don't lose it)

2. pop the extender out and lose up the positioning nut

3. Rotate the extender clock wise (to make the rod shorter) to about half a hole sorter then where the arm is.

4. Force the extender back onto the wastegate arm, put E clip back in and job is done.

Ok so this has gone horribly wrong... The E-clip snapped in the process of getting it off. What do I do now :unsure:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
    • Yup but for me its the HR ! Cut my teeth on the old holden 6s in the day ! And here's me thinking in the day it was also the 300ZX and the Mitsubishi GT3000 ! All, as well had good lines, but always seemed to need finishing off, style wise.
×
×
  • Create New...