Jump to content
SAU Community

Recommended Posts

There is a bore which the pin goes in, and a grove that holds the C clip in place. Its extremely important to squeeze the C clip fully into the holding grove, once in it stays in. I believe he did not sit it fully in to the grove, probably left half of the clip in and half hanging out.

I use C clips to secure turbo bearings as well. I generally squeeze them into the bore slightly above the grove then press it in with tool (a bore size rod), it gives me a "tick" sound once its in the grove, I double check and spin it around in the grove to make sure its secured.

They are little delicate jobs unfortunately it wasn't done correctly. Reflex belive they can sleeve the bore and make some new rings, so things are on track. will post some photos when I get every thing together.

  • 2 weeks later...

Posting a little update:

This is a member with the updated Turbine wheel profile for the 21U high flow (stock R33 turbo).

21u260rwkwboost.jpg

21u260rwkwtorque.jpg

It made of 260rwkws on 15psi of boost. This looks like on factory actuator.

Notice how much the torque curve have improved. Its holding lot better to red line. pretty happy with this ending result.

Thats a nice result Stao You will be pleased to know that my car was fired up last night as well even just running in car feels a heck of a lot more responsive and more torque. for the record i am not putting it on boost and will not rev it over 3000rpm for sometime. with that mod u did on my housing it feels like a totally different turbo :)

Thats a nice result Stao You will be pleased to know that my car was fired up last night as well even just running in car feels a heck of a lot more responsive and more torque. for the record i am not putting it on boost and will not rev it over 3000rpm for sometime. with that mod u did on my housing it feels like a totally different turbo :)

what mod was that?

Posting a little update:

This is a member with the updated Turbine wheel profile for the 21U high flow (stock R33 turbo).

21u260rwkwboost.jpg

21u260rwkwtorque.jpg

It made of 260rwkws on 15psi of boost. This looks like on factory actuator.

Notice how much the torque curve have improved. Its holding lot better to red line. pretty happy with this ending result.

I saw this in the dyno thread its a very good result, but somehow it doesnt seem realitstic, I mean honestly,260kw on 15psi and stock injectors, cmon somethings not right.

The curve is nice though and If 260kw is right its a brilliant result :thumbsup:

Can you also elaborate on your new 2IU upgrade?

Potential buyers will want to know what sort of updates have been made for these great results!

Posting a little update:

This is a member with the updated Turbine wheel profile for the 21U high flow (stock R33 turbo).

21u260rwkwboost.jpg

21u260rwkwtorque.jpg

It made of 260rwkws on 15psi of boost. This looks like on factory actuator.

Notice how much the torque curve have improved. Its holding lot better to red line. pretty happy with this ending result.

I tuned this ecu by mail order.

Power curve is bit flat around 100km/h.

I know boost come down around 2psi.

I found looks like same power curve dyno sheet in http://www.skylinesaustralia.com/forums/topic/261613-hypergear-hiflow-service-continued/page__st__1440

And

Also my tune was done based on 9 sec ramp timing. I also did a comparison run based on 12 sec ramp timing (in red) which many of the dyno section sheets are, longer ramp rate makes all data appear slightly advanced. This is set depending on tuners preferences.

Please tell me what is ramp timing?

I tuned many hiflow turbo and normally smooth curve.

The Shape and figures looks very like 9 sec ramp in comparison to the others did at status. I think you can tune the dip out of 95~115KM/H, Its just like mine with G2, which was just 1 degrees variance in timing.

The Shape and figures looks very like 9 sec ramp in comparison to the others did at status. I think you can tune the dip out of 95~115KM/H, Its just like mine with G2, which was just 1 degrees variance in timing.

,

Thank you for replay.

Yes,if I adjust timing 1-2 degrees around 100km/h , I think dip will fix.

But if he install better boost controller and actuator then more boost , I think dip will fix.

Is this OP6 R34 hiflow?(he does not know so I made map for R34 hiflow)

If so how much is best boost?

Is 14-15psi too low?

,

Thank you for replay.

Yes,if I adjust timing 1-2 degrees around 100km/h , I think dip will fix.

But if he install better boost controller and actuator then more boost , I think dip will fix.

Is this OP6 R34 hiflow?(he does not know so I made map for R34 hiflow)

If so how much is best boost?

Is 14-15psi too low?

This is a 21U turbine housing. From R33 not OP6. For the best shape graph I would perfer boost to peak 20psi at 3500rpms then allow it to drop to 17psi at 7000RPMs with a high pressure actautor. that would give the most mid range.

Can you explain more about the fnt?? can you do this mod to my 43g3?

Yes, or he can provide you with his updated housing that does not use FNT.. Stao thinks the newer .82 is better than the old with FNT but has not posted results for it..

FNT is fixed nozzle technology. It has been explained a couple of times in this thread already (I know the thread is long). Stao machines nozzles into the turbine housing to direct flow to fixed areas of the turbine wheel. I believe he went from a single nozzle to a 3 nozzle and then to a 5, yet has kept on the 3. This would be rather than one uniform groove leading to the turbine wheel.

Hypergear's engine building mate. Obviously doesn't want to take the rap for doing a half assed job on the engine. When it comes down to it, a lot of people will choose money over friendship.

doesnt suprise me, as he was the mechanic at JSA on bell street...

few updates with the engine:

Have got the short motor professionally assembled by Reflex engineering. Had the damaged bore sleeved, with conrods and crank machined to exact clearance. So much differences in terms of professionalism and work quality compare to my "mechanic mate" whom just slapped every thing together with machined block.

shortengine1.JPG

shortengine2.JPG

I've given the short engine to AMR work shop whom rebuild my forged SR20det S14 and CA18det Sil180 back in 2008 with plenty of success in researching ATR28 series.

Also I've been question by one customer about DIY installation of the ATR43SS-1. The SS-1's is harder to install with factory water lines due to limited working space. I had mine fitted by a licensed workshop with every thing done when I picked it up so I did not have photos interms of how it was carried out.

As far as I'm aware, the out side line fits on pretty easily, there are 2 small brackets holding the engine side oil feeding line to the head, they must be removed allowing that extra bit of float for it to reach the feeding port. That water line connects to a bit of rubber pipe behind the inlet manifold.

I've promised to shown DIY work out for the SS-1 so here it is, I've purchased A clean close to stock R33 Spec 2

r33s2rightside.jpg

r33s2leftrear.jpg

With all factory gear including factory heat shield and dump pipe.

enginebay.JPG

I will be aiming for a good responsive 250 streetable rwkws using the SS-1 with fully factory appearace (heat shield and etc goes back on), I will post photos and instructions along as the modifications progresses. (By the way, stock turbo suck, simply out of puff at 4000rpm, Its so slow compare to my guinea pig R33)

Stao, quick question since you mentioned the oil/water lines. Since I replaced my turbo, I've had a fairly slow oil and water leak. Definitely coming from the turbo lines, but I've checked the nuts and they are tight. We definitely put the washers back on and they were in good condition (in fact I seem to recall you gave me new ones for the coolant lines, so they were brand new). Before I pull it apart again, anything I should do??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You are perhaps suggesting that it is not a super car? Well....it's not an AU.
    • Dropped the MX5 of this morning to get the hardtop colour matched and some PDR done, they are also going to give it a buff to remove some "stubborn" swirl marks and light scratches in the clear coat Over the last few months the poor little thing has copped some shopping centre car park abuse, I try to not park in them, but hitting Westfield's a few times over the last few months has taken its toll, nothing really bad, but enough of a trigger for a "while we're in there" thingie  Once it's back and all the one colour, with a few dents and mark's removed I'll give some of these products a go and see what they're like  
    • A locally delivered Infiniti have remote start installed but don't come with the remote start key. You need a new remote start key and they just need it programed. And this is different to making/programing a new key that just starts the car.  
    • Cheers, and cheers for sharing so much of the build and also sharing the glimpse of what turns out to bring a lot of us poor decision makers together haha.  I do recommend learning more about how to manage it, if not considering getting a  formal diagnosis.  The discussion with the psychiatrist I got my diagnosis through was quite eye opening, things I'd not even considered to be ADHD related and hadn't mentioned were things she asked about out of the blue and were common themes with people with my flavour of ADHD.   It's not a label for people who are hyperactive and ill-attentive, there's more to it than that and some of it can be much more challenging or damaging - though there are of course two sides to the thing, and a lot of the stuff we have to go through and work on to live with it make us effectively "better" at other things as well. Aside from the fact that there is some argument I could have a bit of ASD seasoning in there (came up during the diagnosis, and neurodiverse things seem to not stay as a cookie cut) I suspect you need to learn more about ADHD if you are puzzled about how hyperfocus could possibly apply.  I *do* personally use "superpower" with quotes deliberately, but it's 100% an ADHD thing due to the exact reason that lack of focus is also an ADHD thing... Loosely speaking the inattentive side of ADHD isn't the inability to focus, it's the inability to control where the focus goes.  Not being able to sleep because brain is more interested in thinking about a stupid thing I said to a girl I liked 30 years ago, not being able to focus on work because my brain is more keen on putting together the torque management strategy we're going to try out with a drag car next weekend, not being able to focus on a conversation with someone I WANT to listen to and respect because there is a flickering light in my peripheral vision.    If I could just stop work and build the torque management setup right there and then I'd not hear anything else until it was done.  
×
×
  • Create New...