Jump to content
SAU Community

Hypergear Turbochargers and High flow Services Development thread

hypergear

By hypergear,
in Engines & Forced Induction

 Share

Recommended Posts

Crans Mentor

Crans

Posted
Posted

Point him towards the diy section on here, then he can learn how to change injectors without taking the plenum off.

Girl like hands a needed my manly hands couldnt get in to take the plugs off

  • Replies 12.5k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Lithium
Lithium

I was reading through the thread and was going to weigh in anyway, though looks like you're very much on the page I am reading from - so I'll +1 with with a bit more anecdotal evidence to support it

hypergear
hypergear

The ATR28SS15 would be a perfect turbo for your application. I didn't look into some thing even smaller as it doesn't make that much of a difference in response but did loses quite a lot of power. I'

Dose Pipe Sutututu
Dose Pipe Sutututu

^ lol... maybe I'll use a 3" intake pipe and add in more bends.. that usually gets the suuuuuuuuuuuuuuuutuuututuutut going LOL. Anyhow, some real world facts to back up the results.. errbody likes ti

Posted Images

hypergear Grand Master

hypergear

Posted
  • Author
Posted

Point him towards the diy section on here, then he can learn how to change injectors without taking the plenum off.

I've seen Trent doing it while ago. Remove the throttle body, which leaves you with a opening to fit your hand and tools. After removing all the brackets holding the fuel rail and plugs you can pull it out with all the injectors. Do the same putting it back. Not an easy task.

GTScotT Grand Master

GTScotT

Posted
Posted

Easy job. Just be VERY carefull of the spacers under the rail. Easy to drop and lose

This.

Made my life hell for a few days the first time I did it (stupid enough to do it on the grass).

W0rp3D Grand Master

W0rp3D

Posted
Posted

Girl like hands a needed my manly hands couldnt get in to take the plugs off

From memory all you have to do is push down on the clip part and you will hear a click and the plug will slide off, i think i used the tip of a screwdriver to push down on a couple of them.

Easy job. Just be VERY carefull of the spacers under the rail. Easy to drop and lose

I lost them as well, dont try to make some up with old rubber hose that "seems" hard enough to do the job.

also long pointy nose pliers and patience got the job done.

manuel Community Regular

manuel

Posted
Posted

Hey Stao,

I currently have a gcg high flow making 254kw atw with full boost at 3200rpm. This turbo is great on the street with excellent response, great upgrade however i am in need of more power. The GCG turbo spikes at 18psi then drops down to 16psi and stays there untill 7000rpm.

What hypergear option would you recommend to achieve 280 kw plus, with very similar response to gcg high flow. I would like to run the nissan comp cover and also a rear housing which will bolt up to my current dump pipe. Basically im looking for a direct replacment bolton custom turbo which would make some more power.

Also if i decide to keep my gcg high flow can you supply me with a bolton actuator which can hold between 15 to 20 psi. My current actuator was taken of a rb20 turbo and it holds 10psi when boost controller is turned off. I think i might need a stronger one to maintain strong consistant boost, what do you think?

Rolls Grand Master

Rolls

Posted
Posted

Also if i decide to keep my gcg high flow can you supply me with a bolton actuator which can hold between 15 to 20 psi. My current actuator was taken of a rb20 turbo and it holds 10psi when boost controller is turned off. I think i might need a stronger one to maintain strong consistant boost, what do you think?

an electronic boost controller should let you hold 20psi+ to redline, this would almost certainly make 260-270kw which is what you are after yes? With small turbos like this they will always spike boost and then bleed down by redline without an electronic controller.

hypergear Grand Master

hypergear

Posted
  • Author
Posted

For fast response 280rwkws I would recommend the SS1PU version with a 20psi actuator.

By the way I'm doing some modifications to the SS2, not sure if it will work, but if so, I should get 300rwkws with SS1's response.

SargeRX8 Grand Master

SargeRX8

Posted
Posted (edited)

For fast response 280rwkws I would recommend the SS1PU version with a 20psi actuator.

By the way I'm doing some modifications to the SS2, not sure if it will work, but if so, I should get 300rwkws with SS1's response.

If this does work, could something like this be integrated into my turbo if and when I send it back for repairs?

Easy job. Just be VERY carefull of the spacers under the rail. Easy to drop and lose

Ah f**k, I found two of these hard spacers in my engine bay. They were sitting in the engine mount area. Could they be from my rail or something? I didn't fit them in, Advan performance did. Maybe they put new ones in, unless what ever they sit between can work without them...

Edited by SargeRX8
DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Have a feel under where the rail bolts on. Or use a little mirror to see if the black spacer is there.

Wolverine, hahaha, took 3 of us to find that little sucker, that was an injector o ring. I swear it was sucking the blood out of my leg and then just dropped off under the car after we had been searching for a few minutes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT > GTT compatibilities

      By Kinkstaah · Posted

      Ye, in terms of bolting up the "Conversion" from a GT to a GTT is effectively "Use GTT parts for everything" Except the subframe itself, because you won't want a HICAS/4WS subframe. Remember your ABS system will be different too, thanks to GT being the S15 3 sensor system, instead of the R34 4 sensor system for wheel speed. I do not know how people get this to work given R34 diffs do not have a provision for an ABS sensor (they are on the tone wheels of the axles). I assume***** people use S15 gear/R34NA forever when they realize this - Or they convert it to a rear diff/axles that are R33 style which I presume has the singular speed sensor on the diff itself, but then you have to wire it all in and...and... and...
    • GTSBoy
      MLR's Bogan cruise ship

      By GTSBoy · Posted

      Foreshadowing was never so easy.
    • GTSBoy
      Rear hub bolt torque r34

      By GTSBoy · Posted

      The ones in brackets are the first stages of tightening. I usually aim for the middle of the range. They give a range because it's actually not that critical to hit exactly the right bolt tension. Enough is enough, and too much is too much, and the range given is inside that range. Half of the bolts in the suspension are problematic for putting a torque wrench on anyway, so just get done up to mechanic tight  and spanner checked a week later.
    • weikleenget
      R32 GTR clutch master cylinder adapters

      By weikleenget · Posted

      Is the problem that we just disconnected the line, does it need to be plugged? I’d rather not buy another master cylinder
    • GTSBoy
      R34 GT > GTT compatibilities

      By GTSBoy · Posted

      Clutch is same same. Tailshaft is not. Diff will drop in. Half-shafts will not mate up (5x1 on turbo, 3x2 on NA). There is also the strong possibility that your auto NA gets its speed signal from the sensor on the diff, not the gearbag, and that will leave you without a speedo. You can do all this, you just have to do a lot more than you thought.
×
×
  • Create New...