Jump to content
SAU Community

Recommended Posts

That car was with the Nistune with Z32 ECU.

Manifold is good as in haven't cracked yet and there is a slight improvement in up top torque. I will install the G3 back in and see if there are any advantages in overall performance before making quantity and offer to sell.

This housing make lot more down low torque, pretty good to drive as daily.

Can you please PM me with your experience of these guys? I'm not using this turbo but I have some tuning work i need done soon and I have been considering these guys as they are just up the road from me.

For those in WA or Perth with a Hypergear turbo, i would suggest taking it to Garage 101 to get it tuned.

I've mainly had WA customers experiencing problems with tuning, which is also the first time it cames to my awareness as an issue. I've never thought the "tune" would make that much difference as most tuners I've used in Melbourne are good and getting close results.

Also make sure the car is running 100% before taking to the tuners, most of them would just chuck it on the dyno without knowing if there is an issue. becuase of that, figures could be way off the norm and possibly cause damanges to the engine.

I wouldn't blame the tuners around here in the sense that the tune itself is bad, but one thing I can say about a lot of Perth workshops is they don't go the extra mile to diagnose your car. My current tuner and my last tuner are both the same, they are more than willing to help if I'm telling them what I want done but they don't have much to say if it doesn't work as expected. I guess that's fair enough too, they are busy people, but I see the likes of Jez and Trent on here helping people out left right and center and you can tell it translates into their work.

I might give Garage 101 a go if my next tune doesn't have any luck, but unfortunately they are a bit far away from me, can't trailer the car there for the next tune. Looking forward to seeing how it goes though, I'll update when I have a result.

Everything seems to be on track with my build.

The SS1PU is in the car and just waiting on a 24mm socket to fix up the water lines.

Holy hell it was a job and a half in slowly bending the lines to suit the turbo.

The 3' intake is currently on its way.

Should have results by Saturday for everyone.

Please post pics of the intake pipe if u can, where'd did u get it made and how much? Or backyard jobbie.

Scotty mn35 he spends most of his time in the fabrication section.

He is knocking me up one with all the joiners included for around $250

msg-63525-0-69649300-1329650617_thumb.jpg

Spray it black and that's a nice looking intake pipe you have there. I'm getting Racepace to make me up one = $$$$ lol.

Everything seems to be on track with my build.

The SS1PU is in the car and just waiting on a 24mm socket to fix up the water lines.

Holy hell it was a job and a half in slowly bending the lines to suit the turbo.

The 3' intake is currently on its way.

Should have results by Saturday for everyone.

How long do you think the whole job will have taken you by the time you're done? In retrospect would you have paid someone else to do it instead?

With any luck I might have my results by tomorrow night :)

I hope you have the results by tomorrow Birds that would be great.

To be honest I love learning as much as I can about my car so it was worth the time it took.

I started on Tuesday last week with pulling the front bar off respraying that and cleaning the intercooler.

Then I had to wait for a few parts to show up and so all up I think you could do it in 3-4 afternoons.

1 Afternoon taking the dump off and the turbo.

1 Afternoon wiring up the Z32 AFM + Bashing the gutts of the Cat

1 and half afternoons fitting the turbo back and fixing the dump

Stao which G3 model would you recommend for an RB30DET? (older .82 model or FNT revision)

Assume it is a slapper aiming for a very punchy 300rwkw. Will be heavily tracked.

Scotty mn35 he spends most of his time in the fabrication section.

He is knocking me up one with all the joiners included for around $250

msg-63525-0-69649300-1329650617_thumb.jpg

Thanks mate, yeah spray it black as Birds said. Did you just wire up an extra plug on the existing AFM loom for the Z32, I have yet to do mine, and yes its all fun mate.

1 Afternoon wiring up the Z32 AFM + Bashing the gutts of the Cat

I wana do this too but dont want flames shooting out my exhaust and a massive fine too lol. How did you bash it, screwdriver and hammer? haha

I wana do this too but dont want flames shooting out my exhaust and a massive fine too lol. How did you bash it, screwdriver and hammer? haha

lead pipe works better

flames are awesome.

I wana do this too but dont want flames shooting out my exhaust and a massive fine too lol. How did you bash it, screwdriver and hammer? haha

You can get big flames with a cat if you mess with the tune, that or run an atmo bov with a MAF and get the exhaust stinking hot.

Haha read my Sig regarding flames.

I will be spray all my piping black to draw less attention and to get a whole black theme look with my car.

With the cat I just used my boot holder (a long bit of wood haha) + hammer.

To be honest as soon as well put an upgraded turbo and injectors etc. Its not going to pass emissions test anyway.

Ohh and with the Z32 I just wired up a female plug to my car.

Then a male plug to both of the AFM's so its an easy change over

To be honest as soon as well put an upgraded turbo and injectors etc. Its not going to pass emissions test anyway.

Rubbish, that's all in the tune not the hardware. My mechanic builds 500hp+ RB motors regularly and always gets them engineered, they pass the emissions tests no problems.

Rubbish, that's all in the tune not the hardware. My mechanic builds 500hp+ RB motors regularly and always gets them engineered, they pass the emissions tests no problems.

Sorry I should have just said I do not expect to pass one with my new turbo etc.

So I thought why not get the best flow out of my exhaust I could.

Plus flames are fulleh sik

Just a warning on the bashed out cats - they are harder to pick up on than a straight pipe, but the fine for having no cat is substantially more than a standard EPA violation notice for not passing emissions or having illegal mods. From memory it was $2000+

My cat is empty and I've never seen any flames....I am disappoint

Mine is also pretty tame normally, but on the track it was rolling out MASSIVE dragon shit at some stages. It had to do with how rich it was running, after a few consistent laps and a bad rad cap my water temp went a little high and the ecu was compensating with fuel.

Shame nistune doesnt have decel enrichment :( Awesome flames!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Pfft. As if I'd ever point a high pressure washer at my car.
    • The nature of my commute has changed. Way back then it was traffic lights all the way, for ~28km. It sucked. When they finally stitched the expressway together I could do a good 15+km of it at a steady 80-100 with no stopping. That alone has gotten me down to flat 10s. Prior to that it was mid-high 10s. I can't remember the delta that I saw when I got the idle down. It was only ~150 rpm, because the idle speed was never terrible, but for the delta in consumption to be noticeable it would have had to have been at least 0.2-0.3 L/100km - which is not to be sneezed at when it comes for absolute free. It's only about 50L per year, but that's ~$100. A few extra pizzas is always welcome. Note that I have a record of every tank of fuel that has ever gone through my car except for a handful put in by someone else, like my mechanic. I can show you the difference between stock RB20 and tuned RB20, stock RB5Neo and tuned, winter and summer fuel blends, winter and summer fuel blends when the ambient temperature is not appropriate for the blend, working O2 sensor, blown O2 sensor, boosting f**k out of it and frightened to boost it because it is pinging, and so on. OK, I probably can't do all that now with 100% clarity - but at the time when any of those things were in event, you could see it in the records. There's 25+ years of simple tank after tank records, so you have to look for landmarks to work out approximately how old any single record is. What's really important is the meta data and that lives in my head.
    • If you're claiming the issues are not skyline specific, then either the USA is living in the 90s / early 2000s, OR you have the issue of "survivor bias". Which is you're mainly hearing and listening to those with terrible experiences, and haven't found the guys who have cars with good decent builds and no problems. It happens in AU too, that plenty of people keep having issues, and they keep going to the workshops that are known to be shit "because I read on the internet". Even worse, are those who keep posting on the internet as though they know for a fact what something is, when they've never touched/looked at said item in their life, and again are making assumptions, based on something they read, or because it's a certain way in other cars. It's even funnier when those same people debate the facts with the people who've lived and breathed this stuff for over 15 years. Example, I've had someone tell me you can't do something with a Skyline, because they read it on the internet, except I can tell they're wrong, as I did that exact thing back in 2008 with my Skyline.
    • The funniest part I saw, was someone would bitch and moan on FB about something, Andy would be the one to respond, asking for more info, if he could contact them, what the engine setup is, what their config file was, and 95% of the responses were people just going "der! It doesn't work" and Andy going "What doesn't work?" And then going "The firmware!" And they'd go around in circles as no one could ever give information, and Haltech couldn't fault things on the bench, (especially when people wouldn't give any specifics).   Many moons ago, when Andy was back at e420c stage, he reached out to me, and asked me to test different plug and play looms for him (already had an e420c in the car on his V1 PNP loom). And he kept asking me, as I was competent enough to be able to give him some specific feedback on what was/wasn't working, how to replicate the faults etc, and work through things with him. Most people are terrible at answering the questions they're asked, or being able to provide quality feedback other than "it doesn't work".
    • I say it often, none of this stuff is really Skyline-specific per se. But in general there's not a lot of people who actually know what they're doing. A lot of people charging like they do. Agile software development probably isn't the greatest idea for an engine controller.
×
×
  • Create New...