Jump to content
SAU Community

Hypergear Turbochargers and High flow Services Development thread

hypergear

By hypergear,
in Engines & Forced Induction

 Share

Recommended Posts

SargeRX8 Grand Master

SargeRX8

Posted
Posted

Sarge can u hear it pinging? Does it happen on high boost?

What are the afr's doing?

Can't hear anything from the engine bay over the exhaust, the windows up doesn't help. Another thing that doesn't help is the fact that I cant make it happen every time. I can go to the same stretch of road where Ive pinged before, use the same gear, same start speed, same throttle and then no pinging. Its also hard to keep an eye on the AFR but on boost it goes down to about 12 and into the 11's. Ive tried to log it with the laptop but when I put the laptop down in the passenger seat and I drive over a bump in the road the USB cable comes jiggles and I lose connection. Really need someone in the passenger seat and a private stretch of road so I can test it out. Ive watched videos describing what ping would sound like. Some people say its the sound of metal chains dragging behind the car while some would bang a hammer on a piston and say that is what you will hear. Not sure what to make of it. Its not the easiest thing to fang second to redline and listen for ping in a skyline lol.

  • Replies 12.5k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Lithium
Lithium

I was reading through the thread and was going to weigh in anyway, though looks like you're very much on the page I am reading from - so I'll +1 with with a bit more anecdotal evidence to support it

hypergear
hypergear

The ATR28SS15 would be a perfect turbo for your application. I didn't look into some thing even smaller as it doesn't make that much of a difference in response but did loses quite a lot of power. I'

Dose Pipe Sutututu
Dose Pipe Sutututu

^ lol... maybe I'll use a 3" intake pipe and add in more bends.. that usually gets the suuuuuuuuuuuuuuuutuuututuutut going LOL. Anyhow, some real world facts to back up the results.. errbody likes ti

Posted Images

SargeRX8 Grand Master

SargeRX8

Posted
Posted (edited)

maybe not enough throttle enrichment? I had that issue when I smashed the pedal here and there, I added in more throttle enrichment and it went away (just from my personal experience)

Its got some throttle enrichment in there and when I do quick stabs at the throttle the afr richen up abit. Its not the stabs which cause the det, seems I can push the car from 2000 - 6000rpm but it gets into a danger zone at around 6400 rpm.

Take up Jez on the offer and let him have a crack on the dyno. Don't risk your motor TRYING to make it ping on the road.

Yeah Ive been speaking to him, about it. I intend on selling off the current ECU and setup and going with an adaptronic or Haltech plugin. It does seem silly trying to induce knocking especially when its just for logging sake and I know I can't do anything to try fix it.

On a side note, anyone interested in a Z32, PFC, hand controller, greddy profec b sii and the fc edit :P Can't afford the new ecu and tune otherwise.

Edited by SargeRX8
DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Remember it can be false knock. The stock sensors arent perfect. So u dont see the knock go up in datalogit?

How high do u see on the h/controller?

Is the dash light flashing?

DaveO74 Mentor

DaveO74

Posted
Posted

I agree with GTScotT sarge, take JEZ up on the offer dude.

I challenge you to find another tuner who will put your car on the rollers for free.

I have yet to find anyone that puts the extra free time and effort in like JEZ does :)

He actually cares about how a cars running when it leaves his shop.

34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

I agree with GTScotT sarge, take JEZ up on the offer dude.

I challenge you to find another tuner who will put your car on the rollers for free.

I have yet to find anyone that puts the extra free time and effort in like JEZ does :)

He actually cares about how a cars running when it leaves his shop.

JEZ is the man :thumbsup:

34GeeTeeTee Grand Master

34GeeTeeTee

Posted
Posted

be nice if we had someone like jez up this way ! :-(

Where you located? Road trip? :P

Free tuning? Lets go!!

We all wish :yes:

SargeRX8 Grand Master

SargeRX8

Posted
Posted (edited)

Remember it can be false knock. The stock sensors arent perfect. So u dont see the knock go up in datalogit?

How high do u see on the h/controller?

Is the dash light flashing?

Dash lights flash 3 times and when I see that happen thats when I remember to check the hand controller when I park at home. Usually the number is between 85 - 99. Never had a chance to pickup knock in the datalogit.

Edited by SargeRX8
DaveO74 Mentor

DaveO74

Posted
Posted

99! Pffft.

That's nothing sarge (I AM joking dude)

Mine was hitting the 120+ mark, I have heard it once and it is not a sound I would like to hear often.

Makes you ass clench a few times lol

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

That is odd.

Have u tried high boost. It will go in a different part of the map, curious if it pings on high boost. Does it do it only after a hot run?

Time for wmi or e85 sarge :)

Just make sure if u run wmi dont run the wmi out... Hey Dave :P

SargeRX8 Grand Master

SargeRX8

Posted
Posted

Not necessarily after a hot run. I had the car parkes for about 30 mins after a 15 min drive. Gave it a squirt and the flashing light took away from the fun. E85 or flex fueol is where im heading. Wmi is just another thing that could potentially go wrong. Introducing another independant system would scare me lol. I think the flex fuel is the way to go. I tried that octane 100 with 5 or 10% ethanol content and it gave me a slightly better fuel consumption rate and I recall not a single ping event on that fuel. Get ready jez ill be heading up your way soon.

DaveO74 Mentor

DaveO74

Posted
Posted

That is odd.

Have u tried high boost. It will go in a different part of the map, curious if it pings on high boost. Does it do it only after a hot run?

Time for wmi or e85 sarge :)

Just make sure if u run wmi dont run the wmi out... Hey Dave :P

Smartass! :)

I could always blame the boys who put the fluid float switch in lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25RBGT
      Got this r31 silhouette flood car to rebuild.

      By 25RBGT · Posted

      After drying a few days, time to put her back together 
    • Watermouse
      Hypergear Turbochargers and High flow Services Development thread

      By Watermouse · Posted

      Ahh ok, thanks again for your valued insight Tao
    • MBS206
      R32 GTS (RB20DE) clogged cat

      By MBS206 · Posted

      The hot exhaust light will come on not from just the cat being blocked, but it's just a temp sensor, and it's designed to warn you to not do things like park in long grass.   If you've been pushing the motor a bit, it can cause the light to come on.   Second if the cat is rattling, I'd suspect it's not blocked, but instead falling apart inside.   The easiest "fix" until you can get a cat put back in, is to unbolt your one, bash the rest of the insides out, and then bolt it back in.   For a daily driver/street car, I am in agreeance of put a cat in the car. If it were race car I wouldn't care if it were removed.
    • Sean'O
      3D printing fun

      By Sean'O · Posted

      No worries at all 🫡 I think the most satisfying things to make are the little bits that are just impossible to find or they're no longer manufactured. Generally I always try to replace parts with OEM wherever possible. This little project is also great because it'll never see the light of day, but strengthen these brackets so it's not just relying on the little standard screws in the headlight plastic. As soon as I saw the standard brackets and screws I thought, "well I'm not going to install with just the screws, the plastic tabs will just snap off". It's crazy how expensive everything has become yeah. But I suppose that's supply and demand; granted it's a lot easier to get brand new genuine parts these days which is fantastic 😊, I don't have to get totally reamed at the local Nissan dealer ha ha We sure are lucky we have all these manufacturers making parts these days, a few really great Australian companies too like Platinum Racing Products and Fit Mint Automotive, what a time to be alive ❤️ . I've got my eye on the RB26 head by PRP as mine has a very fine hairline crack, so that'll need to be addressed some time in the future. If you have any requests or odd things to make feel free to let me know and I can have a crack at making replacement parts ✌️
    • Duncan
      3D printing fun

      By Duncan · Posted

      Thanks for sharing this, and BTW if your headlights are in good condition they are worth thousands....you might want to consider replacing them with brand new LED ones like this (https://www.nengun.com/78works/full-led-headlights-r32-skyline) and making enough profit to buy a house in Sydney
×
×
  • Create New...