Jump to content
SAU Community

Recommended Posts

that kia must be a laugh to drive....throw some m/ts on the front and go down the princes highway on a friday night...

cheers

darren

About 1 launch and youd snap something lol

Thought there might be some more interest in this thread,

I'm selling an SS1 I recently purchased for my RB20. Need the cash unfortunately.

http://www.skylinesaustralia.com/forums/topic/441479-sa-hypergear-ss1-turbo-brand-new/

Here my dyno results from my ss1.5 on my sr20det non VCt 180sx

266rwkw ss1.5 .86ar

250rwkw ss1.5 .64ar

251rwkw atr28g2 .64ar

Power vs boost

post-79144-13981680622387_thumb.jpg

Power vs torque

post-79144-13981681002793_thumb.jpg

Tuner said there was 5-10kw more in it if I replaced my dw300 fuel pump for a walbro 460lph pump as fuel pressure was dropping 10psi under load when tested but not worth the money and extra to tune right now as turbo is at it's max and injectors will be too as I'm on e85

The .86ar did gain 16rwkw but at 250rpm lag penalty and 5psi more down low and 2-3psi more up top

So it did make the engine happier as he could add in lots more timing and more boost

where as before I was capped to 20psi with .64ar or he had to remove lots of timing with more boost to the point power went down with more boost

Any dyno reading from that tune? The SS2 on Jared's car is the Black edition, with the latest compressor and larger turbine. It should be making power easier then the previous version.

A result sent in from an SS1PU customer. This is the latest version also that has a different compressor that is engineered to hold boost better and more top end.

It is running on E85 maxing out fuel pump. Peek of 301rwkws @ 17psi. With plenty of mid range.

From customer's feed back letter:

R34 GTT (Stock Motor)

Supporting Mods

Blitz FMIC Return Flow

1000cc Injectors

Standard Airbox (Panel Filter)

3inch Bellmouth Full Exhaust

Z32 AFM

Walbro 255 Fuel Pump

SS1PU (latest model)

Scotty's Alloy Intake

CALTEX E-Flex

301.8 Rwkw (18psi peak, drops off to 17psi holds well)

atr43ss1pu.jpg

Is this internal or external gate. Far out there are so many options haha, and I have the exact same mods and I'm getting it done at pulse racing... May save me some time

Drives a lot nicer now it's tuned to the .86rear

Part throttle still has power but haven't done a lot of driving yet as I just got it tuned

But I was surprised it didn't lose much response going from the .64 to .86 200rpm if they where both on 20psi was expecting it to be worse and laggier about 500rpm but engine is a lot happier

Should have waited alil longer as the atr28ss2 would have been a lot better everywhere and make more power down low and up top

Is this internal or external gate. Far out there are so many options haha, and I have the exact same mods and I'm getting it done at pulse racing... May save me some time

This is an internally gated bolton upgrade turbo that sits on factory manifold, dump, and water lines. It is an very responsive turbo for around the 260rwkws mark on P98 fuel. Alternatively you can run the new SS2 which would be good enough for 300rwkws on pump 98 fuel.

This is an internally gated bolton upgrade turbo that sits on factory manifold, dump, and water lines. It is an very responsive turbo for around the 260rwkws mark on P98 fuel. Alternatively you can run the new SS2 which would be good enough for 300rwkws on pump 98 fuel.

I'm missing something - I think his is on E85 and it maxed out making just over 260rwkw? Or you mean 300kw @ hubs?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I mean it's a bit late to say "This won't have any tangible effect and it is not worth spending more than about three seconds on it, please just enjoy the car" But I said it anyway. Does the pod actually get any airflow in that position behind a bumper like that?
    • Hey guys - apologies for digging this up. Has this website been shutdown or is the outage temporary?
    • So, went shopping at Just Jap for things that might work for the intake  After some trial fitting there I ended up with a 3" x 45° silicone bend, a 3" x 300mm alloy straight, and a humped joiner, some minor trimming will be required to shorten some of the stuff, but nothing that is beyond my "ham fisted" skills The guy at Just Jap was most helpful as we had all sorts of joiners,  bends and stuff out trial fitting  Laying it out above the stuff in there it seems everything will fit nicely, and looking at it, it is probably the way I should have been looking at doing it from the beginning, probably..... In the end it is a front bar off job anyway to remove the original stuff behind the front bar that is taking up the required realestate needed, so maybe a Thursday or Friday job And because I'm a hopeless consumer, I grabbed some new steel wheel nuts, the current ones are a spline drive type with a "security" socket, that somehow someone keeps misplacing, the new ones are a basic black steel 17mm hex socket In other news: I just did my "final" tax return, I am now officially a old retired veteran pensioner, and I'm milking the system for all it's worth,  life is good
    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
×
×
  • Create New...