Hypergear Turbochargers and High flow Services Development thread

[Ryno]

I have a mate who's drift car (with RB30/26DET) puts out 450 rwkw through a HDi intercooler. So sure you can force the air through the china cores to make reasonable power... but it begs the question, how much extra power would it make with a decent cooler? At the same time the tune would probably be safer due to lower intake temps.

Edited December 20, 2015 by Ryno

[Badgaz]

has any body tried water spray to increase core cooling? I've seen this make good power difference in the dyno.

[Dose Pipe Sutututu]

has any body tried water spray to increase core cooling? I've seen this make good power difference in the dyno.

I have a mate with a R33 GTS-t with water spray hooked to his IAT sensor.. smart, but you need to always refill it on the track and 1x 2L washer jet bottle doesn't last a full session on the track.

So better to get a more efficient core to start with.

Hopefully when funds permit next year, I will be going straight up to a 100mm Plazmaman core.

[GTSBoy]

has any body tried water spray to increase core cooling? I've seen this make good power difference in the dyno.

I built a system using the Autospeed intelligent water spray controller (which is actually a very clever piece of kit and worth the money) a largish water bottle from a Cordia and a good Bosch windscreen washer pump from a Commodore. Plus a very good atomiser from Spraying Systems. I installed that on my original R32 sidemount. Running the RB20 at 14 psi was enough to make the sidemount marginal - it would heat soak if you drove the car hard. The water spray did an excellent job of keeping the cooler's temp down, and the spray controller made very parsimonious use of the water, so the bottle lasted weeks of street driving. This was all pants-dyno stuff, so not particularly scientific.

When I upgraded to a front mount I could not tell the difference between having the spray working or not, so clearly the cooler was good enough on its own. So I took it all off the car.

[Dose Pipe Sutututu]

if anyone wants my scotty_nm35 intake it's for sale with all silicone joiners/reducers to fit either stock airbox -> hypergear SS2/G3 turbos or pod..

For Sale thread & Photos:

http://www.sau.com.au/forums/topic/461780-fs-syd-r32-r33-scotty-nm35-alloy-intake-pipe-with-4-3-silicon-reducer-good-for-low-mounthypergear-setup-pod/

[jet_r31]

No point

a small wmi jet works much better..

and i bet anything you would like ..using a china core with wi is better than a expensive core heatsoak wise aswell. Was cheap aswell when dollar was good

cheers

darren

[Dose Pipe Sutututu]

No point

a small wmi jet works much better..

and i bet anything you would like ..using a china core with wi is better than a expensive core heatsoak wise aswell. Was cheap aswell when dollar was good

cheers

darren

I'm on E85, so doesn't "really" make a difference in terms of knock.. but because it's not as cold means you make less power and also I have an IAT table that corrects the injection table so it doesn't run rich as crap.

I'm happy to spend my money where it's needed and happy to get rid of my China Racing products (sound racist, but I'm half chongers myself hahahaa)

[Artic Choc]

Im using a plazmaman 76mm core on custom returnflow piping... not hitting any restrictions caused by it as of yet 324kw running 16psi on flex e70... maxed out injectors stopped me running more boost or 284kw 18psi on 98

[t_revz]

No point

a small wmi jet works much better..

Was cheap aswell when dollar was good

Not anymore unfortunately. I want another kit to put on the diesel family wagon but not with today's prices.

[AUSBen31T]

Hey Tao, what turbo do you have to suit an LS1? Have a guy wanting to do an LS1 VL. I was thinking ATR46?

[hypergear]

Best work as a twin, can use two ATR43SS2s, similar to Chequrered tuning's 650rwkws setup. If it has to go Single ATR46 is fine working with two 45mm gates.

[Dose Pipe Sutututu]

Merry Christmas Everyone!

LOL

[kingtube69]

Merry Christmas Everyone!

LOL

Maaaad

Sell me your old one for cheap

[Ke55pig]

Now u just need the cooler to go with the rad

[Dose Pipe Sutututu]

Maaaad

Sell me your old one for cheap

$100 and it's yours man

[thommo458]

another quick question.

Can the ATR45 be supplied with braided lines to suit rather than attempting to make the standard lines fit?

+ pricing

[kingtube69]

another quick question.

Can the ATR45 be supplied with braided lines to suit rather than attempting to make the standard lines fit?

+ pricing

I would also be interested to know - I guess it would be just as easy to get the earls kit though or get custom lines made.

Will wait for Stao's response.

[hypergear]

ATR45SAT comes with braided oil feeding line and uses OEM oil drain. Including the manifold spacer this turbocharger is $1350 inc GST internally gated.

The water lines you can use Earles kits for around $130 from Pirtek. Or you can use push on hoses and fittings, which comes to around $40.

[thommo458]

do you have the earls kits or link to where we can purchase?

[kingtube69]

Here you go sir

http://justjap.com/catalogsearch/result/?q=earls+lines

Stao any idea what size the fittings are for the water then?