Jump to content
SAU Community

18th of OCT - Big turnout needed!!

2rismo

By 2rismo,
in New South Wales

 Share

Recommended Posts

franks Veteran

franks

Posted
Posted
Originally posted by MRK25T

brake pads have been replaced by green stuff, castor rod bushes added, new turbo added, bonnet pins done.

I'm ready

sounds like you're more ready for a trackday than a show and shine mark!

*thread hijak alarm*

Wakefield Trackday 27th October.

MRK25T Experienced

MRK25T

Posted
Posted
Originally posted by franks

sounds like you're more ready for a trackday than a show and shine mark!

*thread hijak alarm*

Wakefield Trackday 27th October.

I'm getting ready for Bendans driver training course.

My tuner wants to do a comparason between the standard AFM I have and the Z32AFM when I get it tuned hopefuly next Saturday.

I really need someone to meet up with if i'm going to get lost in the 'gong. I recall last time 3 of us (including mrturbo) got lost trying to find some beach down there.

I havent heard anything from Prank

2rismo Grand Master

2rismo

Posted
  • Author
Posted

Ummm..... i dunno where ya freaky sydney big-smoke people meet up.... :D I know that there is prob gonna be a group at 6C @ 2pm. Guys from all over gonna come apparently.

suggest ya pm christian and ask what he's doing.

there's also gonna be some that meet for fish and chips at boufllers near south beach (lighthouse) and then cruise the 10 minutes or so to MM (port kembla)

if you guys get lost or need directions, call Paul on 0419432487. He's my official direction giver for the day and will be there for the car shots.

Hope this helps. I wont be on a computer again till probably Tuesday at the earliest so if anyone has any questions, be quick....as in, next 12 hours or so.

Adrian

THANKS GUYS!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R33 GTR lift points for hoist

      By Duncan · Posted

      FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • GTSBoy
      R33 GTR lift points for hoist

      By GTSBoy · Posted

      I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
    • GTSBoy
      R33 GTR lift points for hoist

      By GTSBoy · Posted

      As well as being risky WRT tipping off anyway. Yeah, I wouldn't expect it to move. Just measure from the rear one to the front one on the good side, then measure that same length on the wrecked side. You will find the notches in the pinchweld, and the jacking pad. Just spray a spot of marker paint or something there.
    • sunsetR33
      R33 GTR lift points for hoist

      By sunsetR33 · Posted

      but any other area than the bulge you are talking about will just cave in then? The front driver side is pretty bent so I don't know if that will work the way it is now. I can still kinda make out where that bulge is/was but it looks like the position of it also changed due to all the mistreatment? Hard to tell
×
×
  • Create New...