Jump to content
SAU Community

Power Steering Issue.

Ehgriez

By Ehgriez,
in Western Australia

 Share

Recommended Posts

Ehgriez Mentor

Ehgriez

Posted
Posted

Hey guys.

I've had the strangest issue recently. When I speed up to around 80km/hr I can feel the steering wheel shift to the left and then it stays on an angle until I slow back down where it straightens back up.

I have a feeling that it has something to do with the speed sensitivity of the power steering as it seems to happen at around the point you would expect the steering to be heavier.

Anyone got any ideas on what the issue might be? Only noticed it occurring on Friday.

Cheers,

Greg.

Link to comment
https://www.sau.com.au/forums/topic/262583-power-steering-issue/
Share on other sites
R DIRTY 3 Grand Master

R DIRTY 3

Posted
Posted

Are you talking about the position of the steering wheel?

If so, sounds to me like it might be a loose steering rack on the mounts. Could be caused by worn standard rubber bushes.

Happy to take a look if you need/want. :(

**RB2530** Proficient

**RB2530**

Posted
Posted

Yep this is Hicas playing up...

I have found that whenever I do a wheel alignment or anything where I turn the steering wheel from full lock to lock with the engine off, the Hicas computer goes into some sort of diagnostic mode.

The symptom of this is that the Hicas rack seems free to float or do what it wants. The first thing you notice is you have to correct for this with the steering wheel. Typical the wheel is 10deg of centre on straight road...

The way I fix this particular issue is to stop the car, turn off engine with wheels facing forward. Wait 10-20 secs and then start the car again. All is fine after that.

Now this 'may' be what is happening with your car. OR it could be a fault with Hicas..but definitely something to do with Hicas..

Ehgriez Mentor

Ehgriez

Posted
  • Author
Posted

It seems to be more like 30degrees off centre. It is also perfectly straight at low speed, I can FEEL it shift when i speed up.

R Dirty 3 It would be great if you could have a look sometime, I head up to Ellenbrook pretty often anyway.

Have a HICAS lock bar in my boot, should probably get around to installing it.

Cheers,

Greg.

bubba Grand Master

bubba

Posted
Posted
It seems to be more like 30degrees off centre. It is also perfectly straight at low speed, I can FEEL it shift when i speed up.

R Dirty 3 It would be great if you could have a look sometime, I head up to Ellenbrook pretty often anyway.

Have a HICAS lock bar in my boot, should probably get around to installing it.

Cheers,

Greg.

Put the lockbar in and then take it to Brad to be re-aligned, you won't regret it :P

2LV8ETR Mentor

2LV8ETR

Posted
Posted

Mine did this too.

My problem was the result of the HICAS ring location in the boss kit being out of alignment due to the adhesive coming unstuck.

The HICAS thought that the steering wheel was in a turned position and shot the rear wheels out. Twas funny crabwalking down the road at speed.............

Throw out the HICAS. Best move you could make.

Ehgriez Mentor

Ehgriez

Posted
  • Author
Posted

ok we ripped that shit out tonight, 3 hours or so of work.

Noone mentioned how f**ked up the bolts are that hold in the hicas actuator thingimy, a good hour of that 3 hours was me grunting and pulling at a huge breaker bar to get a 1/8th turn out of the damn thing-.-

Ah well, got it off in the end. Can anyone clarify which of the boxes under my parcel tray is the hicas one? Is it the one stamped with NISSAN on the passenger side, or the other one on the drivers side?

havoc34 Enthusiast

havoc34

Posted
Posted

Hi am new in here. Am driving a R34GTT. Well I seem to have this same problem but mine is the steering wheel to drive stairght I need the steering wheel at abt 5 degrees to the right. Even after alignment done they had to manaully drive and adjust the toe to the fronts for the steering wheel to drive staright but after driving a while it well go back to the same?? Done 3 alignments from differeent places the last was at Malaga Suspensions the got the steering wheel centre but still can when ard 100km/h it starts to pull to the right. Can it be what you guys are talking abt tht my HICAS is also f**ked? And how to confirm? Hope you guys can help me out?? Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • marni
      I need more than help to finish my R33

      By marni · Posted

      Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • r32-25t
      Attesa pump mount options / ideas? R32 gtr style.

      By r32-25t · Posted

      From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      Have you looked at the workshop manual?
    • GTSBoy
      rb25 gearbox mount options - solid mount?

      By GTSBoy · Posted

      Hmm. I've gotten pretty good outcomes from talking to them about things that I've had go wrong or ideas for improvement. Have had a lot to say about the R32 FUCAs, and they have sent out some replacement parts for those, gratis, on a couple of occasions. Mind you, I have bought a couple hundreds of $ of replacement rod ends for them too!
    • FRGTN1
      R34 Manual conversion Speedometer

      By FRGTN1 · Posted

      I have a r34 sedan 1999 manual converted need some help with my speedometer it only reads upto 98km and then stops currently still running the auto cluster any easy fixes no speedo drive is connected yet, if someone has a video for wiring up the manual speedo sensor with the auto cluster please send through 
×
×
  • Create New...