Jump to content
SAU Community

Pss Presents: Fast And Furious 4 Preview Screening 15th April

PSS

By PSS,
in Events

 Share

Recommended Posts

PSS Apprentice

PSS

Posted
Posted

Fast_and_Furious_poster.jpg

Ready for the final install of the epic tale which is Fast and Furious?

PerthStreetScene are proud to have a private preview screen the night before release on the 15th of April! at 7pm so be there well before for a good seat

Tickets are $15 each Sold BEFORE the event.

We will have some hotted up cars in the up stairs carpark at the Morley Galleria so come have a sticky beak and watch a bunch of other car nuts!

Ok... so heres how you get your hands on these hot little tickets..... you have the following options.

1) Sale at drags on Wed Nights, Just track down myself or our PSS girls

2) Sale at Drifts on this Saturday, Just track down myself or our PSS girls

Or.... EFT...

Account name: Perthstreetscene

BSB: 036 067

Account Number: 366 685

Then email me at [email protected] or pm me here with your name,

address,

number of tickets you have bought.

Use your full name as the transfer name thingy so I can identify you.

Remember seats are limited, PSS has the entire cinema but we expect to sell out before the event thus no tickets will be on sale at the door.

SO COME ONE COME ALL!! TELL YOUR FRIENDS! WOOHHOO

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • hypergear
      Hypergear Turbochargers and High flow Services Development thread

      By hypergear · Posted

      Sharing results from recent Liberty Walk R35 GTR, since they are still considered as somesort of a V36 Skyline. We do them turbos too. This are high flowed SS-1 models with ball bearing conversion done.  Car have managed to pull 485awkws @ 20Psi so far pushing limitations of factory built engine. The build list for R35 GTR enthusiasts as follow : HyperGear high flowed stock turbos in SS1 (G25-660 specs) Custom titanium intake pipes. Vspec performance titanium front pipes. Vspec performance 4" titanium exhaust. Upgrade fuel pumps. 1200cc injectors. Ignition coilpacks Hks intake plenum. Hks intercooler piping. Greddy intercooler. Greddy bovs. Top-secret coolant reservoir. Emtron ecu. Straight E85. Built gear box.  
    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      Nah no bearings, just slip fit.  Would be a reasonably challenging but not impossible job to modify it to run bearings but I'm hoping that's not necessary as I may have well built one myself if I end up spending hours modifying it!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Brumbys with good shells are bloody expensive, I've looked at 2 "cheaper" cars, and walked away from both,  plus after some research spare parts are fairly sparce I'm starting to think that I missed the boat on finding a clean one that is straight (ish) and without alot rust I'm starting to think about a old Hilux as panels and other parts are much more available as they sold tens of thousands of them I use to be indecisive but now I'm not sure
    • soviet_merlin
      NC MX5

      By soviet_merlin · Posted

      A Brumby would probably fit a big metal toolbox in the back... this is how it begins  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Picked up a new OEM boot seal for the MX5 today as the old one got ripped a bit by me being a idiot by seeing if I could fit a large metal tool box in it, it didn't fit, and ripped the seal with the corner of the tool box I am still waiting on time to get the cams and new balancer installed, as well as the repairs to the boot Time will not be an issue soon though
×
×
  • Create New...