Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • 2 weeks later...
  • 2 weeks later...
No exactly what the question is...

Doing a burnout? - Drive around the water, backup onto the pad and apply noise.

Isolating the front wheels? - How about one of the Dirtmans 2wd/4wd switch and harnesses...

The 33GTR attessa system if different and you can't just switch from 4wd to 2wd with a switch. You can use a torque split controller but this doesn't fully isolate the rear wheels and isn't good for the transfer case. The proper way to do it is to remove any pressure from the attessa system so that there is no transfer to the front wheels. examples of cars that do this is the heat treatments GTR and Godzilla Motorsports GTR that have a manual pump system to pressurize the transfer case.

There is some combo that you are meant to be able to do, to de-pressurise the transfer case for towing (can't remember it off the top of my head) but it would be a pain in the ass to do on the drag strip.

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4622326
Share on other sites

For an R33/R34 why don't you put in a 3 position solenoid valve in the pressure line that goes to the transfer case and flick a switch to divert all the oil back to the reservior... hence no pre-load? Or is it a mechanical pre-load some how?

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4622549
Share on other sites

To put the GTR into rear wheel drive is simple.

My R33 Service Manual states:-

There are 2 Methods to change the drive mode to 2WD setting.

1. Remove air evacuation connector, and depress the brake pedal 5 times within 10 seconds after placingthe ignition switch to ON posititon. At the same time the 4WD warning lamp will flash in the meter panel (twice in a second) to indicate it's in 2WD mode. To return the the vehicle drive mode to 4WD mode, place the ignition switch to OFF position and connect air evacuation connector.

2. Remove front propeller shaft.

Can anybody confirm this works??

post-47546-1243496825_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4622599
Share on other sites

shit seems like its all to complicated, was hoping for a quick fix way.

ill be doing heaps of passes on the day so hopefully they will warm up due to the mount of use they are getting but i know they wont be perfect.

and yes i do have a torque splitter and already new that the 2wd/4wd switch doesnt work for r33's

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4622688
Share on other sites

For an R33/R34 why don't you put in a 3 position solenoid valve in the pressure line that goes to the transfer case and flick a switch to divert all the oil back to the reservior... hence no pre-load? Or is it a mechanical pre-load some how?

I haven't really looked into it, but something like that could work using a solenoid as I think it pressurizes it when you turn the ignition to acc. Maybe a switch could be rigged up to activate a solenoid to block the line to the transfer case before the car is turned on?

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4623106
Share on other sites

I haven't really looked into it, but something like that could work using a solenoid as I think it pressurizes it when you turn the ignition to acc. Maybe a switch could be rigged up to activate a solenoid to block the line to the transfer case before the car is turned on?

Yeah I would not block it just return it to the reservior, so the ATESSA ecu can do what ever it wants however the transfer case sees no oil hence does not engage 4WD. Not sure if it is that simple.

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4623209
Share on other sites

  • 2 months later...
To put the GTR into rear wheel drive is simple.

My R33 Service Manual states:-

There are 2 Methods to change the drive mode to 2WD setting.

1. Remove air evacuation connector, and depress the brake pedal 5 times within 10 seconds after placingthe ignition switch to ON posititon. At the same time the 4WD warning lamp will flash in the meter panel (twice in a second) to indicate it's in 2WD mode. To return the the vehicle drive mode to 4WD mode, place the ignition switch to OFF position and connect air evacuation connector.

2. Remove front propeller shaft.

Can anybody confirm this works??

post-47546-1243496825_thumb.jpg

i can confirm that it works a treat used it on a dyno and for skids many times

Link to comment
https://www.sau.com.au/forums/topic/264884-gtr-burnouts/#findComment-4762137
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You know, that is exactly the thing that I was thinking a coupe of hours ago. I even had a plan for a meme, involving one big one, another big one, and the Old El Paso girl saying "¿por que no los dos?"
    • NoS, 2 of the big ones.
    • Oh, that's grim. Something bad has been happening there.
    • Put an endoscope down the hole and saw this. Not quite all around the bore but a good 60% at least. Chin to the chest and towards further disappointments I guess.
    • 2 does "sort of" applies, maybe......but looking at what parts would be needed for the swap to get engineered, registered, and insured, and basically that's everything under the car, the modifications the make it legal would be problematic and horrendously expensive, all for a street car that just cruises around and hits a few twisty roads on the weekends Also, from looking at the NSW rules and Regs, with all modifications that is required just to make the car safe and not twist itself to pieces, and then actually get registered for street use, may still be impossible nowadays As for 1, when you add in a fresh engine, fresh transmission, rear cradle and diff, tailshaft, suspension, brakes, cooling, and all the other fabrication required, your probably looking at up to $100k to do it right, all for a 20 year old MX5 that is over engineered and you would never be able to actually use the power it has on the street, much like your beastie, which I love, but you actually track that thing and can use all of its powers in anger, in a safe environment  Hell, the old Bogan Cruise Ship had more power than I could use on the street, and in hindsight, I went a bit silly on that thing, it didn't really need the 500hp it had for what I actually used the car for, it was fun, but basically unusable on the street if you value your licence  As for cams, yeah, I'll probably book it in for them to get installed and tuned soonish, like next month after MX5 Mania are back at work....... and yes, I've already sent a email to bin the turbo quote and quote instead to install cams and a new Fluidampr balancer that will suit the 2.5 better than the OEM 2.0 balancer that is swapped over for the 2.5 install, as the balancer needs to get pulled to time the cams it's a while your in there sort of thing I did think a bit about flex fuel for a laugh, but being na, and no where really around locally anymore to get E85, I've binned that idea, so no sweet sweet corn smells are set for the car I wish E85 was more of a standard fuel, it's better for the environment, better for tuning, plus that sweet sweet smell we all love As for fitting in the family, that's not needed, as everyone in the family already owns a car that can seat 5 humans comfortably enough, the MX5 is "my toy" As for buying a car that is already built, nah, I would rather pick and choose my parts, I enjoy the process, and in the big picture, the additional cost is well worth the enjoyment, and the occasional frustration, I get out of doing it, albeit with other people spinning the spanners, and me, just paying the invoice 🤣
×
×
  • Create New...